Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Connect the TV as shown on the right. Whenever you want to watch the VCR picture, press TV/VIDEO to display the VIDEO indicator in the display window. To a stereo system You can improve sound quality by connecting a stereo system to the AUDIO OUT R/L jacks as shown on the right. :LINE-1 (TV) EURO-AV (Scart) VMC-2121 EURO-AV cable (not supplied) LINE IN AUDIO OUT R/L Audio cable (not supplied) Note • When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in the OPTIONS menu to ON (initial setting). If the TV is connected to the LINE-1 (TV) connector, setting RF MODULATOR in the OPTIONS menu to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 52). Getting Started Step 4 Step 4 Setting up the VCR with the Auto Set Up function Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set TV channels, the VCR clock, guide channels for VIDEO Plus+, and the RF channel. AUTO SET UP AUTO SET UP Hold down AUTO SET UP on the VCR for more than three seconds. The VCR automatically turns on, and the ATP (Auto Tuner Preset) function starts searching for all of the receivable channels and presets them in the appropriate order for your local area. After the search is complete, the current time appears in the display window for any stations that transmit a time signal. If the time does not appear, set the clock manually. See page 22. To cancel the Auto Set Up function Press AUTO SET UP. Note • Do not cancel the Auto Set Up function during the ATP operations. If you do, repeat the step above. Getting Started Getting 11 Step 5 Step 5 Tuning your TV to the VCR If you have connected the VCR to your TV using the EURO-AV cable, skip this step. PROGRAM +/– RF CHANNEL 1 Press RF CHANNEL on the VCR. RF CHANNEL The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV. 2 Turn on your TV and select a programme position for the VCR picture. This programme position will now be referred to as the video channel. 3 Tune the TV to the same channel as that shown in the display window so that the picture on the right appears clearly on the TV screen. Refer to your TV manual for tuning instructions. If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below. SONY VIDEO CASSETTE RECORDER Getting Started Press RF CHANNEL. RF CHANNEL You have now tuned your TV to the VCR. From now on, whenever you want to play a tape, set the TV to the video channel. To check to see if the TV tuning is correct Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct. To obtain a clear picture from the VCR If the picture does not appear clearly in step 3 above, press PROGRAM +/– in step 3, so that another RF channel appears. Then tune the TV to the new RF channel until a clear picture appears. Getting 13 Getting Started Manual setup — Selecting a language If you prefer an on-screen language other than English, use the on-screen display to select another language. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. MENU Joystick >/./?// OK 1 • MENU Press MENU, then push the joystick to >/ . to select SETTINGS and press the joystick (OK). OK PLAY SETTINGS OPTIONS TUNER VIDEO PLUS+ CLOCK LANGUAGE SELECT : SET :OK 2 Push the joystick to >/.to select LANGUAGE, then press the joystick (OK). OK PLAY LANGUAGE ENGLISH NEDERLANDS DEUTSCH DANSK FRANCAIS SVENSKA ITALIANO SUOMI ESPANOL E¤¤HNIKA PORTUGUES SELECT : SET :OK 3 OK PLAY Push the joystick to >/./?//to move the dot ( r) to the desired language, then press the joystick (OK). Note • The menu disappears automatically if you don’t proceed for more than a few minutes. Getting Started Manual setup — Presetting channels If some channels could not be preset using the Auto Set Up function, you can preset them manually. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. PROG +/– MENU Joystick >/./?// OK Getting 15 • MENU Press MENU, then push the joystick to >/ . to select SETTINGS and press the joystick (OK). OK PLAY SETTINGS OPTIONS TUNER VIDEO PLUS+ CLOCK LANGUAGE SELECT : SET :OK OK PLAY Push the joystick to >/.to select TUNER, then press the joystick (OK). NORMAL / CATV CHANNEL SET [ ]C [ ]NORMTUNER AFT [ ]ON FINE TUNING 21 SELECT SET : : PROG10 OK PLAY (SLV-E730EX only) Push the joystick to >/./?//to move the cursor (O) to NORMAL/CATV, then select NORM. To preset CATV (Cable Television) channels, select CATV. NORMAL / CATV CHANNEL SET [ ]C [ ]NORMTUNER AFT [ ]ON FINE TUNING 21 SELECT SET : : PROG10 continued Getting Started Manual setup –– Presetting channels (continued) 4 Push the joystick to >/.to move the cursor (O) to CHANNEL SET. OK PLAY NORMAL / CATV CHANNEL SET [ ]C [ ]NORMTUNER A...
Other models in this manual:Tape Players - SLV-E730UX (610.52 kb)