Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
SECURITY FUNCTION PERSONAL CODE 1 Push the joystick to >/.to select a [WB-1578–– –– ] character. Each time you push the joystick to >, SELECT : the character changes as shown below. SET : CONFIRM :OK A nB n… nZ n0 n1 n… n9 n (blank space) n– (hyphen) nA 2 Push the joystick to / to set the next character. The next space flashes. To correct a character, push the joystick to ?//until the character you want to correct flashes, then reset it. You can set up to 11 characters for your personal code. Getting 27 3 OK PLAY Press the joystick (OK). SECURITY FUNCTION A confirmation screen appears. PERSONAL CODE [ WB-157 8–– ]–– FINAL CONFIRM CANCEL : : CLEAR OK 4 OK PLAY If the displayed personal code is correct, press the joystick (OK). If the displayed personal code is wrong, press CLEAR and continue from step 2. CLEAR To confirm your personal code While the VCR is turned off and there is no tape in the VCR, hold down P PAUSE and ON/STANDBY on the VCR simultaneously for more than three seconds. The entered personal code appears on the TV screen. Press any button to enter normal viewing mode. Notes • The menu disappears automatically if you don’t proceed for more than a few minutes. • Once you enter your personal code, you cannot change it by yourself. If you need to change the entered personal code, consult your nearest Sony service facility. Getting Started Basic Operations Playing a tape NTSC PB 1 2 3 4 5 6 7 8 9 0 6EJECT COUNTER RESET DISPLAY REPLAY Joystick a PLAY P PAUSE )#FF pSTOP 03REW 1 Turn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. Basic Operations Press the joystick (aPLAY). When the tape reaches the end, it will rewind automatically. 3 OK PLAY Additional tasks To Push the joystick to Stop play p STOP Pause play P PAUSE Resume play after pause P PAUSE or press the joystick (a PLAY) Fast-forward the tape )#FF during stop Rewind the tape 03REW during stop Eject the tape Press 6 EJECT. To replay a recently watched scene You can immediately rewind and playback the scene you want to watch again. During playback, press REPLAY up to four times. The VCR rewinds the tape about 10 seconds on the counter for each press of the button, and restarts playback. To play an NTSC-recorded tape Set NTSC PB at the rear of the VCR according to the colour system of your TV. Basic Operations When your TV is Set NTSC PB to PAL only ON PAL TV PAL and NTSC NTSC 4.43 continued Basic Operations Playing a tape (continued) To use the time counter At the point on the tape that you want to find later, press COUNTER RESET. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter. SP VIDEO To display the counter on the TV screen, press DISPLAY. Notes • The counter resets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no recording. • The time counter does not appear on the TV screen when using an NTSC-recorded tape. • Depending on your TV, the following may occur while playing an NTSC-recorded tape: – The picture becomes black and white. – The picture shakes. – No picture appears on the TV screen. – Black streaks appear horizontally on the TV screen. – The colour density increases or decreases. • If you play back a tape in LP or EP mode with NTSC system, the sound is heard in monaural. • While setting the menu on the TV screen, you cannot use the joystick for tape operation. Basic Operations Recording TV programmes 1 2 3 4 5 6 7 8 9 0 COUNTER/ REMAIN TV/VIDEO DISPLAY INPUT SELECT SP/LP rREC PROG +/– Joystick pSTOP Basic Operations Turn on your TV and set it to the video channel. 2 Insert a tape with its safety tab in place. continued Basic Operations 31 Recording TV programmes (continued) 3 INPUT Press INPUT SELECT until a programme position number appears SELECT in the display window. SP VIDEO 4 • PROG Press PROG +/– to select the programme position you want to record. SP VIDEO 5 SP / LP Press SP/LP to select the tape speed, SP or LP. LP (Long Play) provides recording time twice as long as SP, however, SP (Standard Play) produces better picture and audio quality. VIDEO LP 6 REC Press r REC to start recording. The recording indicator lights up red in the display window. Recording indicator LP VIDEO To stop recording Push the joystick to p STOP. Basic Operations To check the remaining time Press DISPLAY. With the display on, press COUNTER/REMAIN to check the remaining time. Each time you press COUNTER/REMAIN, the time counter and the remaining time appear alternately. The remaining time with the indicator also appears in the display window. 1H46M SP Basic Operations Safety tab continued Basic Operations Recording TV programmes (continued) Tips • To select a programme position, you can use the programme number buttons on the remote commander. For two-digit numbers, press the ?(ten’s digit) button followed by the p...
Other models in this manual:Tape Players - SLV-E730UX (610.64 kb)