Votes - 4, Average rating: 4
(
)
)
|
manual abstract
3 Press z REC on this VCR to set it to recording pause. 4 To start editing, press the X PAUSE buttons on both VCRs at the same time. To stop editing Press the x STOP buttons on both VCRs. Tip • To cut out unwanted scenes while editing, press X PAUSE on this VCR when an unwanted scene begins. When it ends, press X PAUSE again to resume recording. Editing Additional Information Troubleshooting If you have any questions or problems not covered below, please consult your nearest Sony service facility. Symptom Remedy The ?/1 ON/STANDBY • Connect the mains lead to the mains securely. switch does not function. Playback Clock Power The power is turned on but the • Moisture condensation has occurred. Turn the power VCR does not operate. off, unplug the mains lead and leave the VCR to dry for over three hours. The VCR is plugged in but the • Set POWER SAVE in the USER SET menu to OFF display window remains dark. (see page 57). The clock has stopped and • The clock stops if the VCR is disconnected from the “– –:– –” appears in the mains. Reset the clock (and timer). display window. The playback picture does not • Make sure the TV is set to the video channel. If you appear on the TV screen. are using a monitor, set it to video input. • If you made connections using the aerial cable only, make sure the RF channel number is set correctly for your area. The picture is not clear. • Existing broadcasts may interfere with the VCR. Reset the RF channel output of your VCR (see page 17). • Adjust the tracking with the TRACKING +/– buttons on the VCR. • The video heads are dirty (see the last page of Troubleshooting). Clean the video heads using the Sony T-25CLD, E-25CLDR, or T-25CLW video head cleaning cassette. If these cleaning cassettes are not available in your area, have the heads cleaned at your nearest Sony service facility (a standard service charge will be required). Do not use a commercially available liquid type cleaning cassette other than Sony’s, as it may damage the video heads. • The video heads may have to be replaced. Consult your local Sony service facility for more information. Additional Information The picture has no colour. • The COLOUR SYSTEM option in the USER SET menu is set to the wrong position. Set the option to conform to the system that the tape was recorded in. The picture rolls vertically • Adjust the vertical hold control on the TV or monitor. during picture search. continued Additional Information Troubleshooting (continued) Symptom Remedy Recording Playback The picture has no sound. • The tape is defective. • If you made A/V connections, check the audio cable connection. • If you made connections using the aerial cable only, make sure the TV system is set correctly for your area. The sound from a tape • Adjust the tracking. recorded with the VCR is not • The video heads are dirty. Clean the video heads in stereo or the STEREO using the Sony T-25CLD, E-25CLDR, or T-25CLW indicator in the display video head cleaning cassette as explained above. window is flashing. No TV programme appears on • Make sure the TV is set to the video channel. If you the TV screen. are using a monitor, set it to video input. • Existing broadcasts may interfere with the VCR. Reset the RF channel output of your VCR (see page 17). • Select the correct source with the INPUT SELECT button. Select a programme position when recording TV programmes; select a line input when recording from other equipment. TV reception is poor. • Make sure the aerial cable is connected securely. • Adjust the TV aerial. • Make sure the TV system is correctly set for your TV. • Make sure TV SYSTEM (B/G, D/K, I, B/B, U.S–ANT., U.S–HRC, U.S–IRC or JAPAN) in the INSTALLATION menu is set to the same system in your local area. The recorded picture has no • Set COLOUR SYSTEM in the USER SET menu colour or unusual colour. according to your local colour system. The tape starts playing as • The safety tab has been removed. To record on this soon as it is inserted. tape, cover the tab hole (see page 34). The tape is ejected when you • The safety tab has been removed. To record on this press z REC. tape, cover the tab hole (see page 34). Nothing happens when you • Make sure the tape is not at its end. press z REC. Additional Information Symptom Remedy The timer does not operate. • Check that the clock is set. • Make sure a tape has been inserted. • Check that the safety tab has not been removed. rding • Make sure the tape is not at its end. reco• Make sure a programme has been set for timer recording. Timer• Make sure your timer settings are past the current time. • The clock stops if the VCR is disconnected from the mains. Reset the clock and timer. • Turn the power off and unplug the mains lead. A tape cannot be inserted. • Check that a tape is not already in the tape compartment. The remote commander does not function. • Make sure you are pointing the remote commander at the remote sensor on the VCR. • Replace all the batteries in the remote commander w...
Other models in this manual:Tape Players - SLV-ED323ME (584.27 kb)
Tape Players - SLV-ED323SG (584.27 kb)
Tape Players - SLV-ED825PS (584.27 kb)
Tape Players - SLV-ED828ME (584.27 kb)