Votes - 1, Average rating: 3 ( )

Manafacture: Maytag File size: 543.97 kb File name: Language of manual:

(For single story installations UXT3030AA and UXT3036AA hoods only.) FIG. E. Ducting between the ceiling joists FIG. F. Straight up through the roof (for multi-story installations) or through the using 6" round duct (for single-story soffit space above the cabinets (where the installations). soffit connects to an outside wall). 1. Unpack hood and check contents. You should receive: 1 -Aluminum Filter (UXT3030AA, UXT3036AA, UXT2030AA and UXT2036AA hoods only) 1 -3." x 10" Damper/Duct Connector (mounted inside of hood for shipping only) ((UXT3030AA and UXT3036AA hoods only) 1 -Ductfree Filter (UXT4030AA and UXT4036AA hoods only) 2. Remove wiring box cover. Under cover find: 1 -Plastic Bag containing loose mounting hardware 2 (This section for UXT2030AA, UXT2036AA, UXT3030AA, andUXT3036AA hoods only. UXT4030AA and UXT4036AA hoodsskip this section and go on to "Prepare the Hood".) Begin planning ductwork by deciding where duct will run between the range hood and the outside. For best performance, use the shortest possible duct run and a minimum numaber of elbows. There are several choices shown - FIGS. A - F below. FIG. A Ducting directly through the wall (for range hoods mounted on an exterior wall). Shown are two ways to duct through an outside wall. If a wall cap is used directly off the back of the hood, special care must be taken to make sure that the damper in the damper/duct connector on the hood damper in the wall cap do not interfere with each other when the hood is operating. This could result in either inadequate air delivery or backdrafts. If this condition does exist, remove the hood damper flap. Sometimes when using a wall cap it is easier to duct vertically and then use an elbow as shown FIG. B. In more complex ducting situations, a 3-1/4" x 10" rectangular ducting range hood (UXT3030AA and UXT3036AA hoods) can be converted to a round duct by means of a transition. FIG. C. Straight up through the roof using 7" round duct (for single story installations - UXT2030AA and UTX2036AA only) PREPARE THE HOOD - CONT. PREPARE THE HOOD - CONT. 3. Remove top or rear electrical knockout. (FIG. 2) 5. (UXT3030AA AND UXT3036AA ONLY). Install damper/duct connector over opening made in STEP 4. Use #8B sheet metal screws provided. (FIG. 3) UXT2030AA and UXT2036AA hoods ONLY) Install Model 87 damper (purchase separately) over opening in top of hood. FIG. 2 4. (UXT3030AA and UXT3036AA hoods ONLY) Remove duct knockout. Insert screwdriver under edge of knockout, break tabs, and peel knockout back with pliers. (FIG. 3) FIG. 3 PREPARE THE INSTALLATION LOCATION Omit STEP 1 if hood will be installed under cabinets with flush bottom. 1. (For installation on recessed bottom cabinets only) Attach a wood filler strip at each side of recessed are under cabinet. Use two 1" x 2" strips cut to length. If recess is deeper than 1" use thicker strips. Attach strips with 1-1/4'' wood screws, 3" from end end of strip. See FIG. 4. 2. Measure and mark the following (FIGS. 5A & 5B): a.) Electrical wiring opening in wall or cabinet. b.) Duct opening in wall or cabinet. (UXT2030AA, UXT2036AA, UXT3030AA, and UXT3036AA ONLY) FIG. 4 FIG. 5A FIG. 5B UXT2030AA UXT2036AA UXT3030AA UXT3036AA UXT4030AA UXT4036AA 3 3. Use 1-1/4" bit to drill opening for electric wiring. 4. Cut out duct opening in wall or cabinet with saber saw or keyhole saw. 5. Center hood in installation opening and trace keyhole slots onto wood filler str...

Download now

Please, enter two numbers from picture: