Votes - 3, Average rating: 4 ( )

Manafacture: Maytag File size: 543.97 kb File name: Language of manual:

Install damper/duct connector over opening made in STEP 4. Use #8B sheet metal screws provided. (FIG. 3) UXT2030AA and UXT2036AA hoods ONLY) Install Model 87 damper (purchase separately) over opening in top of hood. FIG. 2 4. (UXT3030AA and UXT3036AA hoods ONLY) Remove duct knockout. Insert screwdriver under edge of knockout, break tabs, and peel knockout back with pliers. (FIG. 3) FIG. 3 PREPARE THE INSTALLATION LOCATION Omit STEP 1 if hood will be installed under cabinets with flush bottom. 1. (For installation on recessed bottom cabinets only) Attach a wood filler strip at each side of recessed are under cabinet. Use two 1" x 2" strips cut to length. If recess is deeper than 1" use thicker strips. Attach strips with 1-1/4'' wood screws, 3" from end end of strip. See FIG. 4. 2. Measure and mark the following (FIGS. 5A & 5B): a.) Electrical wiring opening in wall or cabinet. b.) Duct opening in wall or cabinet. (UXT2030AA, UXT2036AA, UXT3030AA, and UXT3036AA ONLY) FIG. 4 FIG. 5A FIG. 5B UXT2030AA UXT2036AA UXT3030AA UXT3036AA UXT4030AA UXT4036AA 3 3. Use 1-1/4" bit to drill opening for electric wiring. 4. Cut out duct opening in wall or cabinet with saber saw or keyhole saw. 5. Center hood in installation opening and trace keyhole slots onto wood filler strips on cabinet bottom. 6. Screw four #10 x 7/8 wood screws into exact center of narrow end of traced keyhole slots. Allow 3/8" of screws to project, so that hood can be fitted into place later. INSTALL THE DUCTWORK PREPARE THE INSTALLATION LOCATION - CONT. WARNING WHEN CUTTING OR DRILLING INTO WALL OR CABINET, BE CAREFUL NOT TO CUT EXISTING ELECTRICAL WIRING. FIG. 6 (This section for UXT2030AA, UXT2036AA, UXT3030AA, andUXT3036AA hoods ony. UXT4030AA and UXT4036AA hoodsskip this section and go on to "Install Range Hood".) NOTE These instructions will follow plans made on Page 2. Startat the exterior and run ductwork back to the range hood. For best possible performance, use the shortest possibleduct run and a minimum number of elbows. Do not vent a range hood into an attice space. A buildup of grease in theattic could become a fire hazard. Use only metal ductwork. DO NOT USE PLASTIC DUCT. Assemble duct run securely so that in case of a greasefire on the range, the fire will be contained inside metalductwork. Tape all duct connections. 2. Follow appropriate directions below for type of duct run you install. a.) Wall Cap Discharge; (FIG. 7) Use saber saw or keyhole saw to to cut hole slightly larger than duct size used so that duct will line up easily with damper/duct connector on hood. Install casing strips if cap will be installed on siding. Attach required amount of duct to wall cap and run duct back to hood. Fasten cap to wall and caulk well. FIG. 7 b.) Roof Cap Discharge: (FIG. 8) Cut a hole in roof slightly larger than duct size being used. Run ductwork down to hood location. Leave 3/4" of duct projecting above roof surface on high side. Trim duct parallel to roof pitch and seal all around duct with roof cement. Carefully trim shingles and slide back of roof sheet under shingles. Nail roof sheet to roof under shingles at top two comers and two sides. Nail sheet directly to roof in four places at bottom. Using roof cement, seal all nail heads and shingles which were cut or lifted. Do not seal bottom edge of roof sheet. FIG. 8 4 INSTALLING RANGE HOOD WARNING TURN OFF THE PROPER CIRCUIT AT THE SERVICE ENTRANCE BEFORE WIRING THIS ...

Download now

Please, enter two numbers from picture: