Votes - 0, Average rating: 0
(
)
)
|
manual abstract
1. Release the scraper safety catch 2. Use the blade to clean the hob surface Do not attempt to clean the hob surface with the base of the scraper. This could result in scratching. : Risk of injury! ! The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Care of the appliance Apply an additive to protect and preserve the hob. Follow the advice and warnings provided with the product. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are generally caused by minor faults. Before contacting the Technical Assistance Service, make sure you have read the following recommendations and warnings. Indicator Malfunction Measure none The electric power supply has been interrupted. Use other electrical appliances to check if there has been a power cut. The appliance has not been correctly connected following the connection diagram. Make sure that the appliance has been connected correctly. Electronic system malfunction. If in the above checks, the malfunction is not resolved, contact the Technical Assistance Service. * If the warning persists call the Technical Assistance Service. Do not place hot pans on the control panel. Indicator Malfunction Measure “ flashing The control panel is wet or an object is Dry the control panel area or remove the object. resting on it. “§ + number / Electronic system malfunction. Disconnect the hob from the mains. Wait 30 seconds or so, then con- s + number / nect it again. * . + number ”‹ / ”S There is an internal error in the system. Disconnect the hob from the mains. Wait 30 seconds or so, then connect it again. * ” . The electronic system has overheated and Wait until the electronic system has cooled down completely. Then the corresponding hotplate has been press any symbol on the hob. * switched off. ” … The electronic system has overheated and all hotplates have been switched off. —‚ Supply voltage outside normal operating Please contact the local electricity board. limits. —. / — „ The hotplate has overheated and switched Wait until the electronic system has cooled down sufficiently before off to protect its working surface. switching it back on. * If the warning persists call the Technical Assistance Service. Do not place hot pans on the control panel. Normal noise while the appliance is working Induction heating technology is based on the creation of electromagnetic fields that generate heat directly at the base of the pan. Depending on how the pan has been manufactured, these may produce certain noises or vibrations such as those described below: A deep humming sound as in a transformer This noise is produced when cooking on a high power level. It is caused by the amount of energy transferred from the hob to the pan. The noise disappears or becomes faint when the power level is lowered. A low whistling sound This noise is produced when the pan is empty. It disappears when water or food is added to the pan. A crackling sound This noise occurs in pans which are made from different materials superimposed on one another. It is caused by the vibrations that occur ajoining surfaces of the different superimposed materials. The noise comes from the pan. The amount of food and cooking method can vary. A high- pitched whistling sound This noise is produced mainly in pans made from different materials superimposed on one another, and it occurs when such pans are heated at maximum power on two hotplates at the same time. The whistling disappears or becomes fainter as soon as the power level is lowered. Noise from the fan For proper use of the electronic system, the temperature of the hob must be controlled. For this purpose, the hob has a fan that starts working after detecting excess temperatures at different power levels. The fan may also work due to inertia after the hob has been switched off, if the temperature detected is still too high. The noises described are normal, they are part of induction heating technology and not a sign of malfunction. After-sales service Our after- sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call- out. E number and FD number: Please quote the E number (product number) and the FD number ( production number) of your appliance when contacting the after-sales service. The rating plate bearing these numbers can be found on the appliance certificate. Please note that a visit from an after-sales service engineer is not free of charge, even during the warranty period. Please find the contact data of all countries in the enclosed customer service list. To book an engineer visit and product advice GB 0844 8928979 Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of...
Other models in this manual:Cooktops - PIX611E14E/20 (1.27 mb)