EML E-Series
HP
e2400-FC 4G
interface
StorageWorks
controller
replacement
Caution: Parts can be damaged by
Note: This part is not hot-pluggable.
electrostatic discharge. Keep parts in their
It is necessary to power down the library
containers until needed. Ensure that you
to replace this part.
are properly grounded when touching
Note: When installing the interface
static sensitive components.
controller, additional insertion force is
needed to seat this card.
1
2
EML
e2400-FC 2G
Interface
HP
Controller
StorageWorks
Upgrade
Caution: Parts can be damaged by
To power off the library,
electrostatic discharge. Keep parts in their
containers until needed. Ensure that you
are properly grounded when touching
Caution: Before continuing with this
static sensitive components.
ry firmware
procedure, ensure the following components
are upgraded to the necessa
versions:
a. Verify that all jobs have completed processing.
• Library:
er:
• Interface Manag
Note: This part is not hot-pluggable.
• Command View ESL:
It is necessary to power down the library
to replace this part.
Refer to the HP StorageWorks Interface
nd Command View User Guide
Manager a
for detailed procedures on checking
f
irmware revisions and making updates.
b. Using the Operators Control Panel (OCP),
Note: You will find an animation of
this procedure on the documentation
CD shipped with your library..
select Operations > Unlock Door. The robot
1
ES
L
E
-
s
eries
In
t
erface
Manager
h
p
1
0
0
2
6
N
o
te: This part is not hot-pluggable.
I
t

i
s necessary to power down the library
S
to
rageWorks
t
o

r
eplace this part.
should now be parked.
C
a
ution: Parts can be damaged by
e
l
e
ctrostatic discharge. Keep parts in their
c
ontainers until needed. Ensure you are
p
roperly grounded when touching static-
2
s
e
n
sitive components.
br
a
ry off-line by pressing the
P
o
w
er down the library.
a
. Place the li
S
t
a
ndby button on the library's front panel.
T
h
e library robotics completes any current
c
ommands and then stops.
b
.
Verify that the front panel display indicates
“System Off-line”.
c
. Verify that the picker is empty. If there is a
2
1
t
a
p
e cartridge in the picker, perform a Move
c
o
mmand to place the cartridge in an
a
vailable slot. [Content needed.]
d
.
P
ress and hold the power button located on
U
t
h
e

front of the library behind the laptop tray
When the power is on, the ACT/LNK LEDs wil
u
n
t
i
l the front panel goes blank.
4
be off instead of green; the power LED might also
I
n
s
p
ect the contents of the kit.
be off. You may need to find out which drives are
3
F
l
i
p
the two breaker switches off at the power
connected to each interface controller to identify
d
i
s
t
ribution unit.
t
he controller to be replaced.
O
p
en the back door of the library.
To power off the library,
c. Open the back doors of the library.
a. Stop all library activity and ensure that the
picker is empty.
door at the rear of the rack.
b. Open the
c. Set the rack power switch at the upper right
corner to the OFF position.
d. Ensure that all power indicators on the power
supplies are off.
d. Press the main power switch to the O (Off)
Inspect the contents of the kit. You will need a
flat-blade screwdriver to remove and replace this
tape drive.
position.
Inspect the contents of the kit.
Removal
3
4
Locate the interface controller (IC) in the second
card cage slot in the base module or in one of
HP recommends labeling the cables before removing
the slots in the card cage expansion module. This
them. Noting cable locations for later reconnection,
IC has a FC0, FC1, TD0, TD1, TD2, TD3, one
carefully disconnect the FC and Ethernet cables
Ethernet, and one serial port. You will need a #1
from the interface controller by pressing on the
Phillips screwdriver to remove and replace this card.
connector tabs and removing the cables.

---

...

Other models in this manual:
Media Storage - HP EML 103e Tape Library (1.42 mb)
Media Storage - HP EML 245e Tape Library (1.42 mb)
Media Storage - HP EML Base Library (1.42 mb)
Media Storage - HP EML E-Series 103e Base Tape Library (1.42 mb)