Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
HP
EML E-Series
Drive Module
StorageWorks
Replacement
Caution: Parts can be damaged by
Note: This part is hot-pluggable. You do
electrostatic discharge. Keep parts in their
not need to power down the library to
containers until needed. Make sure that
replace this part.
you are properly grounded when touching
static sensitive components.
Note: You can find an animation of the
1
removal process on the documentation CD
that shipped with the tape library.
EML E-Series
Dr e
HP
StorageWorks
Note: This part is hot-pluggable. It is not
necessary to power down the library to add
t
his part, however, the library does have to be
power-cycled when adding or replacing a drive.
Caution: Parts can be damaged by
Note: A new drive will not be recognized
electrostatic discharge. Keep parts in their
hen touching
by the library until after a reboot.
containers until needed. Ensure that you
are properly grounded w
static sensitive components.
Removal
2
1
E
S
L
E
-
s
eries
I
n
t
erface
I
f you are removing an existing tape drive,
M
anager
h
p
1
0
0
2
6
N
o
te: This part is not hot-pluggable.
I
t
i
s
necessary to power down the library
S
t
o
rageWorks
t
o
r
eplace this part.
make sure to unload any tape cartridges in
C
aution: Parts can be damaged by
e
l
e
ctrostatic discharge. Keep parts in their
c
ontainers until needed. Ensure you are
properly grounded when touching static-
2
s
e
n
sitive components.
the drive to be removed using your application
P
o
w
er down the library.
a
. Place the library off-line by pressing the
S
t
andby button on the library's front panel.
T
h
e library robotics completes any current
c
ommands and then stops.
b
.
Verify that the front panel display indicates
“System Off-line”.
1
software or the library GUI touch screen. Use
c
.
V
erify that the picker is empty. If there is a
t
ape cartridge in the picker, perform a Move
c
o
mmand to place the cartridge in an
a
v
ailable slot. [Content needed.]
d
.
P
ress and hold the power button located on
t
he front of the library behind the laptop tray
u
nt
i
l
the front panel goes blank.
your backup software to cease library activity.
4
I
n
s
pect the contents of the kit.
3
F
l
i
p
the two breaker switches off at the power
d
i
s
tribution unit.
O
p
en the back door of the library.
f the kit. You may need a
I
nspect the contents o
flat-blade screwdriver to remove and replace this
tape drive.
4
3
Identify the tape drive to be replaced. The Fault
LED light may be lit, signifying a hot swap can
occur.
Removal
Open the back door
of the library.
2
Inspect the contents of the kit. You may need a
screwdriver to remove and replace this tape drive.
If you are removing an existing tape drive,
make sure to unload any tape cartridges in
the drive to be removed using your application
software or the library GUI touch screen. Use
3
your backup software to stop library activity.
Open the back
doors of the library.
...Other models in this manual:
Media Storage - HP EML 103e Tape Library (1.17 mb)
Media Storage - HP EML 245e Tape Library (1.17 mb)
Media Storage - HP EML Base Library (1.17 mb)
Media Storage - HP EML E-Series 103e Base Tape Library (1.17 mb)