Votes - 4, Average rating: 3.5 ( )

Manafacture: Impex File size: 383.17 kb File name: 9627fe4a-d2db-4d77-bc81-7decb24dfc3a.pdf Language of manual:

Find the markings inside the battery compartment showing which direction the batteries must be turned. Insert the batteries into the battery compartment. Attach the Monitor Bracket (27) to the back of the Electronic Monitor (46) with the four Console Screws (44). Insert the Handlebar Shaft (54) into the Frame (1). Plug the Sensor Wire (21) into the wire on the Electronic Monitor (46). Attach the Monitor Bracket with the Monitor to the Frame (1) with two 3/16O Small Screws (2). Make sure that the Sensor Wire is not pinched between the Electronic Monitor and the Frame. Carefully bundle the extra Sensor Wire (21) and console wire together and insert the wires under the Electronic Monitor (46). Do not insert the wires down into the Side Shields (50, 51). 4. Install both of the Access Covers (14) into the holes in the Side Shields (50, 51) as shown. 1 49 1 49 19 40 40 39 32 52 42 2 3 3 48 32 1 43 3 3 46 Battery Compartment 27 46 44 44 21 1 46 54 2 27 4 50 14 51 5 5. Lubricate the Handlebar Shaft (54). Slide the Right Handlebar (36) onto the right end of the Handlebar Shaft. (Note: See the drawing on the front cover to make sure that the Right Handlebar is turned correctly.) Slide the Left Handlebar (37) onto the left end of the Handlebar Shaft. Tap a 5/8" Push Nut (35) onto each end of the Handlebar Shaft. 6. Slide an M8 Washer (5), a Link Arm Bushing (47) and a Link Arm (26) onto the threaded pin on the lower end of the Left Handlebar (37). Make sure that the Link Arm Bushing is turned so the flange is next to the Washer, and that the opening in the end of the Link Arm is downward as shown. Tighten an M8 Locknut (32), with an M8 Washer (5), onto the threaded pin. Attach the other Link Arm to the Left Handlebar (not shown) in the same manner. 5 35 36 37 54 35 6 37 26 Flange 5 47 5 32 7. For your convenience, the pedal assemblies have been pre-assembled by the factory. Remove the 1/2" Locknut (23) from the end of one Pedal Shaft (16). Slide the 17.5mm Washer (56) onto the shoulder of the Pedal Shaft and firmly tighten the Pedal Shaft clockwise into the right arm of the Crank (18). Next, tighten the 1/2O Locknut (23) onto the Pedal Shaft. Make sure that the 17.5mm Washer (56) can be moved back and forth on the shoulder of the Pedal Shaft. If the 17.5mm Washer cannot be moved back and forth on the shoulder of the Pedal Shaft, it will be impossible to correctly attach the Link Arms (26). Fit the end of the right Link Arm (26) onto the Pedal Shaft and slide the Link Arm onto the Pedal Bushing (25). Attach the other Pedal to the left arm of the Crank (not shown) in the same manner. 26 1816 23 7 25 56 Shoulder 6 HOW TO USE THE EXERCISE CYCLE HANDLEBAR OPERATION The handlebars can be used in either the stationary mode, for pedaling exercise only, or the dual-action mode, for both upper-body and lower-body exercise. STATIONARY MODE To convert the handlebars to the stationary mode, the Link Arms (26) must be disconnected from the pedals. Pull the Link Arms outw...

Download now

Please, enter two numbers from picture: