Votes - 6, Average rating: 3.5
(
)
)
|
manual abstract
b: As you slide the threaded shaft (845) through the aligned holes . (D) Secure the cylinder head with two M8x15mm Allen Head Bolts (843). (E) Repeat this procedure to assemble the Adjustable Cylinder on the right side of the frame. 826 X2 843 X4 845 X2 846 X2 25 ASSEMBLY STEP 8: Assembly front plastic shrouds (A) Attach the outer Left Upright Plastic Shroud - LL (311) , the inner Left Upright Plastic Shroud - LR (312) and the Adjustable Cylinder Cover – Upper(315)to the Left Upright - L (301) and secure with five M8 x 20mm Screws (806) and five 4 . 15mm Thread Cutting Screw (807). (B) Repeat the above process for the Right side 806 X10 807 X10 26 9.45ST TREADMILL ASSEMBLY STEP 9:Securing of the Upright Tubes NOTE: ONLY TURN BOLTS CLOCKWISE. The Allen Bolt Sets (412) have been pre-assembled in the Base Frame(401). (A) Secure The Upright Tubes by tightening the Allen Bolt (412), located in the Upright Tube, clockwise. 27 STABILIZER ADJUSTMENT FOLLOW THESE INSTRUCTIONS TO LEVEL YOUR TREADMILL: An uneven floor or improper stabilizer level can cause the treadmill to wobble during use as well as the incline adjustment to function incorrectly. Please follow the procedure described below to make sure the treadmill stabilizer is adjusted correctly prior to use. You may need the assistance of another person to perform this adjustment. First locate the two adjustable stabilizers under the base frame. Then simply rotate them in or out to adjust the level of the treadmill. When properly adjusted the treadmill should sit firmly on both stabilizers and all cushions. Locate the two adjustable stabilizers under the base frame. Treadmill should sit firmly on both stabilizers and all cushions. 28 9.45ST TREADMILL FEATURES Serial Number Location Insert safety key The safety key must be inserted for the treadmill to function. The safety key clip should be worn at all times when the treadmill is in use. This safety feature is designed to prevent injury. 29 MOTION CONTROL OPERATION 29 MOTION CONTROL OPERATION MOTION CONTROL: Walking belt speed can be increased, decreased or stopped using the Motion Control sensors on the handlebars. To do this follow the instructions below: 1. Press the button on the console to switch the motion control function on and off: • When the LED light is ON the MOTION CONTROL is active. • When the LED light is OFF the MOTION CONTROL is off. 2. After switching on the MOTION CONTROL wave your right hand approximately 6 inches above the motion sensor on the right handle bar to increase the speed. The sensor will sound one short BEEP per scan and speed up by 0.1 MPH per BEEP. Holding your right hand approximately 6 inches above the right sensor constantly results in the sensor sounding one long BEEP per second and speeding up by 0.5 MPH per second. 2. Use right sensor to speed up. 3. Wave you left hand approximately 6 inches above the motion sensor on the left handle bar to decrease the speed. The sensor will sound one short BEEP per scan and decrease speed by 0.1 MPH. Holding your left hand approximately 6 inches above the left sensor constantly results in the sensor sounding one long BEEP per second and decreasing speed by 0.5 MPH per second. 3. Use left sensor to slow down. 4. Wave both hands approximately 6 inches above both motion sensors at the same time. The sensor will sound two short BEEP sounds then stop the belt. • Always switch off the motion control function by pressing the MOTION CONTROL button on the console before turning off the power to the treadmill. 4. Use both sensors to stop belt. 30 9.45ST TREADMILL MAINTAINENCE 9.45ST TREADMILL MAINTAINENCE HOW TO MAINTAIN THE 9.45ST TREADMILL: Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance could cause damage or shorten the life of your treadmill and exceed the LIMITED WARRANTY coverage. • Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids away and keep it out of direct sunlight. • Inspect and tighten all parts of the treadmill regularly. Replace any damaged or worn parts immediately. BELT ADJUSTMENT: ALL BELT ADJUSTMENTS ARE CONSIDERED MAINTENANCE, AND ARE THE RESPONSIBILITY OF THE END USER. Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been adjusted properly at the factory. However transportation, uneven flooring or other unpredicted reasons could cause the belt to shift off center resulting in the belt rubbing on the plastic side rail or end caps and possibly causing damage to the equipment. To adjust the belt back to it’s proper position please follow the directions below: • Walking belt has shifted to the left: First unplug the power cord from the surge protector. Using the hex key provided, turn the left rear roller adjustment bolt 1/4 turn in the clockwise d...