Votes - 1, Average rating: 3
(
)
)
|
manual abstract
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/television technician for help. Care and precautions 1) Use a soft dry cloth to clean the machine. 2) Use only AA size alkaline batteries. 3) Do not expose the machine or the tape cassette to high temperature, high humidity or excessive dust. 4) If you do not intend to use the machine for an extended period of time, remove the batteries. 5) Do not touch the cutter lever when printing or while replacing the cutter unit. 6) Do not touch the cutter blade. 7) Do not put the tapes in your mouth. 8) Do not stick tapes onto your skin. Putting in the batteries 1) To remove the battery compartment cover, press down firmly on the triangular catch located on the end of the machine furthest from the tape cutter, and pull the battery compartment cover away from the P-Touch so that it disengages. 2) Remove the old batteries and insert six new AA size alkaline batteries, rriaking sure that their orientation is as shown in the illustration engraved on the inside of the case. The three batteries on top all point in one direction, while the three underneath point in the opposite direction. When inserting new batteries, always insert them positive end first. When removing old batteries, always remove them negative end first. Always replace worn out ba tteries with brand new ones, and always replace all six at once. 3) To replace the cover, fit the tabs on the cover into the slots in the P-Touch case and push down firmly on the catch at the opposite end of the cover so that the cover snaps securely back into place, Accessories The following accessories are available: Tape cassettes 1/2" (12 mm) 3/8" (9.mm) $9.89 (SRP) Jtóí&i?)',, Black on silver M-931 M-921. Black on gold M-831 №821 Black on blue M-531 M-521 Black on green M-731 .VI-721 Black on pink M-E31 M-E21 Replacement cutter unit TC7 $9.95 (SRP) Most retailers and distributors carry a full line of tape cassettes. If you wish to order accessories for your P-Touch direct from Brother, please refer to the "Accessory Order Form" included separately. Changing the cutter unit If the cutter becomes blunt and ccascs to cut the tape cleanly, replace it. 1) Open the cassette compartment. 2) Grasp the tab on the cutter unit and lift it out, taking care not to touch the blade or the cutter lever. 3) Insert a new cutter unit. If the cutter lever is stuck in the pushed-in position, rotate the new cutter unit as you insert it, to push the lever back into its normal position. ^ CAUTION ____— • When changing the cutter unit, be sure not to touch the cutter blade. • Make sure that small children do not try to put the cutter unit in their mouths. Changing the tape cassette 1} To remove the tape cassette compartment cover, press the textured area of the catch located on the end of the machine closest to the tape cutter. 2) Press down firmly on the catch so that the cover hinges up, then remove it. 3) Lift out the old cassette. Remove the paper tab from the new tape cassette. Make sure that the end of the tape in the new cassette feeds through the guide posts on the cassette. 4) Insert the tape cassette, making sure that it clicks into place. Ensure that the cassette sits properly on the two metal posts. Tape exit slot 5) To replace the cover, fit the tab on the cover into the slots in the P-Touch case and push down firmly on the cover so that it snaps securely back into place. 6) Hold down the ©> key and press the (g key, then cut the tape. The amount of tape left is visible through the zvin-dow in the back of the P-Touch. When there is only a little tape remaining, the tape becomes green. Cleaning If dust accumulates on the print head, one or more unprinted horizontal lines may appear on your labels. Should this happen, clean the P-Touch as follows, 1) Turn off the P-Touch. 2) Open the cassette compartment and remove the cassette. 3) Wipe the print head and pinch roller up and down using a dry cotton swab. 4) 5) Replace the cassette, replace the cover, switch on, FEEO hold down the 0} key and press the ,g| key to feed the tape, and try a test print. If the tape is still speckled with dust, repeat steps 1-4, this time using a cotton swab dipped in rubbing alcohol. Function keys Tape cutter Space key •) ON key - © Press © to switch the P-Touch on. To conserve battery power, the P-Touch automatically switches itself off if no key is pressed for five minutes. When the batteries are low, "BATT" appears on the display when you try ...