Votes - 4, Average rating: 4.5 ( )

Manafacture: Tecumseh File size: 448.09 kb File name: 3d6e0d15-a532-07b4-89d6-019429624afa.pdf Language of manual:

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED WITH THE EQUIPMENT ON WHICH THIS ENGINE IS USED BEFORE ATTEMPTING TO OPERATE YOUR TECUMSEH ENGINE. A THESE SYMBOLS MAY APPEAR ON THE ENGINE: FAST SLOW STOP OFF FULL IGNITION KEY INSERT TO RUN REMOVE TO STOP CHOKE California Proposition 65 WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 3-1-00 181-637-14 181-637-14 ENGINES WHICH ARE CERTIFIED TO COMPLY WITH CALIFORNIA AND U.S. EPA EMISSION REGULATIONS FOR ULGE ENGINES: Are certified to operate on regular unleaded gasoline. Include the following emission control system(s): EM, TWC (if so equipped); Do not include any user adjustable features - therefore no other adjustments are needed. OIL & FUEL RECOMMENDATIONS TO OPERATE ENGINE, YOU WILL NEED THE FOLLOWING: • A CLEAN, HIGH QUALITY DETERGENT OIL. Be sure original container is marked: A.P.I. service "SF" - "SJ". FOR SUMMER (ABOVE 320F; 00C) USE SAE 30 OIL. Tecumseh specially formulated oil is available at any Authorized Tecumseh Service Outlet. Order as part number 730225. Using multigrade oil will increase oil consumption. FOR WINTER (BELOW 320F; 00C) USE SAE 5W30 OIL. Tecumseh specially formulated oil is available at any Authorized Tecumseh Service Outlet. Order as part number 730226. (SAE 10W is an acceptable substitute.) (BELOW 00F; -180C ONLY): SAE 0W30 is an acceptable substitute. DO NOT USE SAE 10W40 OIL. OIL SUMP CAPACITY: 21 ounces (1-1/4 U.S. pints) .62 liter * *A FRESH, CLEAN, UNLEADED REGULAR, UNLEADED PREMIUM OR REFORMULATED AUTOMOTIVE GASOLINE ONLY. DO NOT USE LEADED GASOLINE. NOTE: DO NOT USE GASOLINE CONTAINING METHANOL (WOOD ALCOHOL). Gasoline containing up to 10% ethanol or grain alcohol ("Gasohol''), or up to 15 MTBE (Methyl Tertiary Butyl Ether), may be used but requires special care when engine is unused for extended periods. See "STORAGE" instructions on Page 5. NOTE: Use clean oil and fuel and store in approved, clean, covered containers. Use clean fill funnels. Never use "stale" gasoline left over from last season or stored for long periods. BEFORE STARTING • READ ALL INSTRUCTIONS PROVIDED WITH THE EQUIPMENT ON WHICH THIS ENGINE IS USED. * TO FILL OIL SUMP OR CHECK OIL LEVEL: IMPORTANT: To avoid engine damage never run engine unless: - Oil level is between "FULL" and "ADD" marks on dipstick. - Oil fill plug is tightened securely into oil fill tube or hole. CHECK OIL LEVEL OFTEN DURING ENGINE BREAK-IN. A. POSITION EQUIPMENT SO ENGINE IS LEVEL. B. Clean area around oil fill plug (see Figure 1). C. Remove oil fill plug and dipstick. D. Wipe dipstick clean, insert it into oil fill hole and tighten securely. Remove dipstick. If oil is not up to "FULL" mark on dipstick, add recommended oil. POUR SLOWLY. Wipe dipstick clean each time oil level is checked. IMPORTANT: DO NOT FILL ABOVE "FULL" MARK ON DIPSTICK. E. Install oil fill plug and dipstick, tighten securely. See "MAINTENANCE" section for further oil instructions. P BEFORE STARTING (Continued) • FILL FUEL TANK: A. Clean area around fuel fill cap, remove cap. B. Add "UNLEADED" regular gasoline, slowly, to fuel tank. Use a funnel to prevent spillage. IMPORTANT: NEVER MIX OIL WITH GASOLINE C. Install fuel fill cap and wipe up any spilled gasoline. A NEVER FILL FUEL TANK INDOORS. NEVER FILL FUEL TANK WHEN ENGINE IS RUNNING OR HOT. DO I NOT SMOKE WHEN FILLING FUEL TANK._ Л NEVER FILL FUEL TANK COMPLETELY. FILL TANK H TO 1/2" BELOW BOTTOM OF FILLER NECK TO PROVIDE SPACE FOR FUEL EXPANSION. WIPE ANY FUEL SPILLAGE FROM ENGINE AND EQUIPMENT BEFORE STARTING ENGINE._ Л ANY LIQUEFIED PETROLEUM (LPG) OR NATURAL ЛШ, GAS FUEL SYSTEM MUST BE LEAKPROOF AND I MEET ALL APPLICABLE CODES AND REGULATIONS. • CHECK THE FOLLOWING:_ A. BE SURE EQUIPMENT IS IN NEUTRAL GEAR WITH A CLUTCHES, BELTS, CHAINS AND SAFETY SWITCHES DISENGAGED. (FOLLOW EQUIPMENT MANUFACTUR-I ER’S INSTRUCTIONS.) THIS SHOULD PLACE ANY | SAFETY SWITCHES IN SAFE STARTING POSITION. B. Be sure spark plug wire is attached to spark plug (see Figure 1). C. Be sure: - Ignition switch on engine or equipment is in "ON", "RUN" or "START" position. OR - Ignition key (if so equipped see Figure 2) is inserted into ignition keyslot in carburetor cover (see Figure 1). DO NOT TURN IGNITION KEY. D. Be sure fuel valve is open (see Figure 3). ENGINE WILL NOT START UNLESS IGNITION KEY IS INSERTED INTO IGNITION KEYSLOT IN CARBURTER q COVER. DO NOT TURN IGNITION KEY __ IGNITION KEY Figure 2 s FUEL VALVE \JL \ TURN CLOCKWISE TO 1 "OFF" POSITION "OPEN" POSITION SHOWN / Figure 3 2 181-637-14 STARTING STARTING (Continued) A NEVER RUN ENGINE INDOORS OR IN ENCLOSED, 14 POORLY VENTILATED AREAS. ENGINE EXHAUST CONTAINS CARBON MONOXIDE, AN ODORLESS AND DEADLY GAS (CARBON MONOXIDE IS ALSO PRESENT IN ENGINE EXHAUST FROM LIQUID PETROLEUM (LPG) AND NATURAL GAS FUEL ...

Download now

Please, enter two numbers from picture: