|
Other manuals for this model:
manual abstract
Use the number buttons on your remote to enter numbers and the arrow buttons to move from one entry field to another. 5. When done, press the RETURN button on your remote. 6. Select NetworkTest to check the Internet connectivity. 04 Advanced Features 7. Set Internet Protocol Setup to Auto. 8. Auto acquires and enters the needed Internet values automatically. 9 When done, press the RETURN button on your remote. 10. If the Network Function has not acquired the network connection values, go to the directions for Manual. Network Setup IP Address : Subnet Mask : Gateway : DNS : Auto DNS Server : U Move E Enter R Return Internet Protocol Setup : Auto > English 29 30 English Advanced Features ¦¦ Connecting to a Wireless Network To connect your TV to your network wirelessly, you need a wireless router or modem and a Samsung Wireless LAN Adapter (WIS09ABGN, WIS09ABGN2, WIS10ABGN), which you connect to your TV’s back or side panel USB jack. See the illustration below. Samsung’s Wireless LAN adapter is sold separately and is offered by select retailers, Ecommerce sites and Samsungparts. com. Samsung’s Wireless LAN adapter supports the IEEE 802.11A/B/G and N communication protocols. Samsung recommends using IEEE 802.11N. When you play the video over a IEEE 802.11B/G connection, the video may not play smoothly. ..NOTE xx You must use the “Samsung Wireless LAN Adapter” (WIS09ABGN, WIS09ABGN2, WIS10ABGN) to use a wireless network. xx Samsung’s Wireless LAN Adapter is sold separately. The Samsung Wireless LAN Adapter is offered by select retailers, Ecommerce sites and Samsungparts.com. xx To use a wireless network, your TV must be connected to a wireless IP sharer. If the wireless IP sharer supports DHCP, your TV can use a DHCP or static IP address to connect to the wireless network. xx Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently being used by another device nearby, this will result in interference and communication failure. xx If you apply a security system other than the systems listed below, it will not work with the TV. xx If Pure High-throughput (Greenfield) 802.11N mode is selected and the Encryption type is set to WEP, TKIP or TKIPAES (WPS2Mixed) for your AP, Samsung TVs will not support a connection in compliance with new Wi-Fi certification specifications. xx If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode. xx If your router, modem, or device isn’t certified, it may not connect to the TV via the “Samsung Wireless LAN Adapter.” xx Connection Methods: You can setup the wireless network connection six ways. –– Samsung Auto Configuration –– PBC (WPS) –– Auto Setup (Using the Auto Network Search function) –– Manual Setup –– SWL(Samsung Wireless Link) –– Ad-Hoc xx The Samsung Wireless LAN Adapter may not be recognized or work properly when connecting via a USB hub or via a USB extension cable other than the one available from Samsung. TV Rear Panel (HDD) The LAN Port on the Wall LAN Cable Wireless IP sharer (AP having DHCP server) Samsung Wireless LAN Adapter or .. To use the SWL(Samsung Wireless Link) function, connect to the USB 1 (HDD) port. Notice The picture may appear corrupted or have static for some channels when the TV is connected to the Samsung Wireless LAN Adapter. In such a case, establish a connection using one of the following methods or connect the Samsung Wireless LAN Adapter using a USB cable in a place that is not affected by radio interference. Method 1 Method 2 04 Advanced Features Connect using the USB right angle adapter or Network Setup (Samsung Auto Configuration) This function is available in APs (Access Points) that support Samsung Auto Configuration. If your AP does not, you can connect through PBC (WPS), auto, or manually. . This function is available when SWL(Samsung WirelessLink)is set to Off. . You can check for equipment that supports Samsung Auto Configuration on How to set up using Samsung Auto Configuration 1. Place the AP and TV next to each other and turn them on. . Because the booting times of applications differ, you may have to wait for approximately 2 minutes. . If the LAN cable connected the WAN port of AP during Samsung Auto Configuration, you are able to complete until internet connection test. If you do not connect, Samsung Auto Configuration will check only device connecting of AP (Not check internet). 2. After 2 minutes, connect the Samsung Wireless LAN Adapter to the TV. When the Samsung Wireless LAN Adapter is established, the pop-up window appears. 3. As soon as a connection is established, place the AP in parallel with the Samsung Wireless LAN Adapter giving a gap no larger than 25cm. Connect via an extension cable . The Samsung Wireless LAN Adapter should be installed in an interferenc...
Other models in this manual:Televisions - UE32C6700US (21.69 mb)
Televisions - UE32C6710US (21.69 mb)
Televisions - UE32C6740SS (21.69 mb)
Televisions - UE37C6700US (21.69 mb)