Votes - 4, Average rating: 4
(
)
)
|
manual abstract
On-screen display for sleep timer 26 E Press SLEEP repeatedly until OFF is displayed. After 5 seconds of inactivity, the message will disappear. Use of the Remote Control with Other A/V Products Programming the Remote Control to Use with Other Brands of Audio and Video Products: (Figures 1-3 this page, figures 4-5 following page) 1. Move the slide switch at the top of the remote to the product you want to control. 2. Press and hold the POWER button on the remote control. 3. Enter the first three digit code listed for your equipment, and then release the POWER button on the remote control. 4. Point the remote control to the equipment and press the POWER button. Note: If the equipment responds, the remote control is properly programmed to operate the equipment. If the equipment does not respond, repeat steps 2-4 with the next three digit code listed in step 3 for your equipment. CABLE/DBS/DTV VCR DVD TV- ' I r -AUDIO I I I I I i. a 2 POWER 3. Cable Box Codes Cable box brand Code to enter: General Instruments/ Jerrold 119, 120, 121, 122,123, 124 Motorola 125, 126, 127 Oak 139, 137, 102 Pioneer 101, 116 Scientific Atlanta 112, 113 Zenith 117, 100 If your cable box code is not listed here, please see page 66 for a complete listing. To reset to default code, enter ООО Figure 1. Programming the remote to control your cable box. I IMPORTANT I If you cannot turn the cable box ON by pressing POWER, try pressing CHANNEL or the number buttons. I 1.C з CABLE/DBS/DTV VCR DVD TV- 1 I Г -AUDIO I I I _L TD 2 POWER, Satellite Receiver Codes Satellite brand Code to enter: Mitsubishi DTV - DBS 006 DishNetwork 175 Hughes - DBS 173 Panasonic - DBS 174 RCA - DBS 176 Sony - DBS 177 Toshiba-DBS 170, 173, 189, 190, 191 To reset to default code, enter ООО If your satellite receiver code is not listed here, please see page 67 for a complete listing. Figure 2. Programming the remote to control your satellite receiver. I IMPORTANT I , When set to TV, the PLAY, STOP, REW/REV, and FF/FWD buttons will operate the VCR after the VCR codes have been properly programmed into the remote control. I CABLE/DBS/DTV VCR DVD TV- 1 I Г —AUDIO 1.C з. i i i i i VCR Codes 2 POWER] VCR brand Code to enter: Mitsubishi 001,002 Hitachi 020, 043, 065 JVC 030,054 Phillips / Magnavox 043, 044, 051 Panasonic 041,042, 043 RCA 020, 053, 065 Sony 048, 049, 050 Toshiba 021 If your VCR code is not listed here, please see page 67 for a complete listing. To reset to default code, enter ООО Figure S. Programming the remote to control your VCR. 27 Use of the Remote Control with Other A/V Products CABLE/DBS/DTV VCR DVD TV- 1 I Г -AUDIO __I I I I I i. 3. DVD Player Codes 2 POWER DVD/LDP brand Code to enter Mitsubishi 003 JVC 257 Panasonic 250 Philips 258, 253, 272 Pioneer DVD 252 Samsung 261 Sony 254 Toshiba 253 If your DVD code is not listed here, please see page 66 for a complete listing. To reset to default code, enter ООО After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed. If you enter a code from the AUDIO chart while the slide switch is set to TV, the volume and mute functions change to match the A/V receiver. This is useful when using an A/V receiver with the TV all the time. In all other cases, only one of the below devices is allowed for each slide switch position. Figure 4. Programming the remote to control your DVD or LDP. i 3. Figure 5. Programming the remote to control your A/V receiver. I IMPORTANT I CABLE/DBS/DTV-, VCR „DVD TV- 1 I Г -AUDIO I I I I_ С I Ж 2. A/V Receiver Codes Audio brand Code to enter: Mitsubishi A/V receiver G1G, G15, G11, G12, and/or CD player 013, G14 Denon 234, 235, 236, 245, 246, 359 Harman Kardon 215, 223, 242 JVC 233, 232 Kenwood 2G8, 2GG Marantz 224, 35G Onkyo 2G9, 214, 24G, 247 Pioneer 2G5, 2G7 Sony 222, 249 Technics 218, 219, 221 Yamaha 2G2, 2G1, 243, 244 If your audio code is not listed here, please see page 66 for a complete listing. To reset to default code, enter ООО TV position: Q TV Q A/V receiver (volume and mute only) Cable/DBS/DTV position: Q Cable box Q Satellite receiver Q DTV receiver VCR position: Q VCR DVD position: □ DVD Q LD Player Audio position: Q A/V receiver Q Mitsubishi CD player If you have a Mitsubishi A/V receiver, the audio position may be used in conjunction with select Mitsubishi CD players. Your audio position must be programmed to either 010 or 011. Plug the CD player power cord into a switched outlet on the back of your A/V receiver. Pressing the POWER button turns On the A/V receiver, along with the CD player. In the audio position, for some CD players, the transport controls (FF, Play, Rew, etc.) operate the CD player. I IMPORTANT I _» If the slide switch is set to TV when you enter an A/V receiver code, VOLUME and MUTE will control the A/...
Other models in this manual:Televisions - WS - 48313 (4.1 mb)
Televisions - WS - 48313 (4.1 mb)
Televisions - WS - 55313 (4.1 mb)
Televisions - WS - 65313 (4.1 mb)