Votes - 4, Average rating: 4
(
)
)
|
manual abstract
1.2 Insert the out-door antenna into the antenna socket on the cabinet back. Adjust the direction or position of the outdoor antenna for the best possible picture. 2. POWER SWITCH 2.1 Press the power switch when the power is off, the indicator (red) lights up, the screen is dark, the TV is in standby mode. 2.2 If you want to cut off the power completely, and do not-want to use On Timer function, press the Power Switch again to disconnect the set's power and confirm that the indicators go out. 3. PANEL OPERATION: MANUAL TUNING MANUAL TUNING PRESET ON/OFF AUTO PRESET AV/TV 2 3.1 STANDBY ( ) Button 3.1.1 Press STANDBY ( ) button to turn on the set (the indicator shows yellow) when the set is in STANDBY mode (the indicator shows red) , the channel position number is displayed in the screen. Press STANDBY ( ) button to return the set to the STANDBY mode when the set is in OPERATION mode, and the indicator shows red. 3.2 CHANNEL PRESET 3.2.1 AUTO PRESET 3.2.1.1 Press PRESET ON/OFF button to set PRESET mode. The current band and channel position will be displayed on screen. (In green) 3.2.1.2 Press AUTO PRESET button, the appliance will search for the signal of TV stations in the order of VHFL, VHFH and UHF as shown in the following and memorise them from channel number 1 position. UHFVHFL VHFH 3.2.1.3 When presetting is over, the channel position is set to number 1 automatically. 3.2.1.4 Press PRESET ON/OFF button to exit preset mode. NOTE: * During presetting, the green bar turns into yellow. The moving bar indicates the change of tuning frequencies. * During presetting, auto presetting will be cut off if any one of STAND BY button, PRESET ON/OFF button or AUTO PRESET button is pressed. 3.2.2 MANUAL TUNING 3.2.2.1 Press PRESET ON/OFF button to set preset mode. 3.2.2.2 Select a channel position. If "SKIP" displays on the screen, press "SKIP" button to exit "SKIP" mode. SKIP 8 VHFH 8 SKIP lllllllll..... llllllllll..... 3.2.2.3 Press and hold MANUAL TUNING button until your desired program appears. UHF VHFH VHFL MFT UHFVHFHVHFL 3 3.2.2.4 Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position, 3.2.2.5 Repeat 1~ 4 steps to search another channel. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased. * If some channel position is tuned by MANUAL TUNING mode, AFC (automatic frequency control) function is defeated in this channel position. 3.3 SKIP BUTTON 3.3.1 FUNCTION When CHANNEL SELECTOR ( )button is used to select channel, the channels will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing is as shown. 1 8 9 99 0 (REMOTE) (THE APPLIANCE) CHANNEL DECREASE CHANNEL INCREASE 1 8 9 99 0 CH CH CH 3.3.2 OPERATION: 3. 3.2.1 Press PRESET ON/OFF button to set preset mode. 3. 3.2.2 Select a channel by using CHANNEL SELECTOR button. 3.3.2.3 Press "SKIP" button, "SKIP" will be-displayed on the screen to indicate that the channel is at "SKIP" mode. SKIP 3 SKIP llllllllllllll 3. 3. 2. 4 Repeat 2~3 steps to skip another channel. 3. 3. 2. 5 Press PRESET ON/OFF button to exit preset mode. 3.4 CHANNEL SELECTION 3.4.1 This set is preset to Australia channels 2, 7, 9, 10, 28 on those numbers. If you wish to change the settings, or add more channels the method is quite straight forward. 3.4.2 Press CHANNEL SELECTOR ( )on the appliance, the channel number will be increased or decreased as shown in the following Fig. , and displayed in the upper right corner of the screen. 4 CHANNEL INCREASE CH 0 CH CH 1 2 3 99 8 CHANNEL DECREASE (REMOTE) (THE APPLIANCE) 1 2 3 99 0 3.5 VOLUME CONTROL 3.5.1. Press the VOL button to increase volume ; the green bar on the screen moves right. 3.5.2. Press the VOL button to decrease volume ; the green bar on the screen moves left. Display of minimum volume Display of maximum volume ......................... 3.6 AV/TV SELECTOR Press AV/TV button to change TV mode to AV mode when the set is in receiving (TV) mode. On the contrary, press it to change AV mode to TV mode when the set is in VIDEO mode. 3.7 TINT CONTROL Use this knob to control colour tone during reception of pictures when using the NTSC system. 5 4. REMOTE CONTROL OPERATION: REMOTE CONTROL UNIT : CHANNEL SELECTOR 1 ~ 9 : DIGITAL CHANNEL SELECTOR : STANDBYCH VOL : VOLUME CONTROL PPS : PERSONAL PREFERENCE SELECT 10/0 : CHANNEL 10 OR CHANNEL 0 SELECTOR (BRIGHTNESS, COLOUR) SYSTEM : COLOUR SYSTEM CONTROL : PICTURE/TIME ADJUSTMENT -/- -: DIGIT OR TWO DIGIT CHANNEL PICTURE : PICTURE CONTROL SELECT DSP : DISPLAY : PREVIOUS 4.1 INSTALLING BATTERIES: 4.1.1 Remove the battery cover of Remote Control Unit. 4.1.2 Insert two "AAA", 1.5V batteries, making sure the polarity ( + or - ) of the batteries matches the polarity marks inside the unit. 4.1.3 Close the battery cover NOTE: * When the Remote Control Unit is not used for a long time or t...