© Copyright 2006 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. Contents PRODUCT SPECIFICATIONS................................................... 3 GENERAL SAFETY RULES ..................................................... 3 Specific Safety Rules ........................................

® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. For technical questions, please call 1-800-444-

3. Insert the Handle (4) into the Handle Sockets (3) and mount the Handle Sockets to the Side Panel B (1) top using supplied hardware. Note: The Handle (4) configuration may differ slightly than what is shown in this manual. 4. Lift Side Panel B (1) all the way to expose the wire spool and Wire Feed Mechanism (11). Wire Feed Mechanism (11)Wire SpoolWire Spool Axle (10) Side Panel B (1) (C) (D) (34) – + 5. Remove the Nut from the Wire Spool Axle (10). Place the Wire Spool over the Axle with the w

If there is any doubt, do not attempt to use this product. 5. USE EYE, HEARING, BREATHING, AND HAND PROTECTION. Wear an ANSI approved welding helmet/goggles with shaded lens, hearing protectors, breathing respirator, and welding gloves when using this product. ANSI approved welding helmet/goggles with shaded lens, hearing protectors, breathing respirators,and welding gloves are available from Harbor Freight Tools. 6. DRESS SAFELY. Sparks and hot metal can injure. Always wear body protection. Non

Bend at joint Cross Section Possible Causes and Solutions 1. Improper clamping: Make sure that pieces are clamped securely in place. Make tack welds to help hold pieces. 2. Excessive heat: Weld a small portion and allow to cool before proceeding. Reduce wire feed speed. Increase weld speed. 10. When the weld is complete, lift the electrode wire clearly away from any grounded object, set the Face Shield down, turn toward the Flux Wire Welder, and turn the Power Switch to the OFF position. 11. Unp

of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not weld. Maintenance12. . For your safety, service and maintenance should be performed regularly only by a qualified technician. This helmet provides protection 13. for intended purposes only. There are certain applications for which this helmet was designed. Do not modify this helmet and do not use this helmet for a purpose for which it

Keep your head out of the fumes. SKU 91124Page 4 REV 05/04 3. Avoid eye and body damage. Arc rays and infrared radiation can injure eyes and burn skin. Wear ANSI approved eye and body protection. Do not allow viewing by visitors without proper eye and body protection. Use the provided Face Shield with arc shaded filter plate. 4. Know proper arc welding practices. Read and understand the manufacturer’s instructions, as well as your employer’s safety practices for arc welding. 5. Connect only to a

Contaminants will interfere with the welding process, and may cause noxious gasses to be produced as they are heated during the welding operation. 2. Always connect the Ground Clamp to another cleaned location as close as possible to the work area (no more than 12” away). NOTE: Always wear and use ANSI-approved personal safety clothing and safety devices to reduce the risk for injury. Spot Welding Washers using the Magnetic Washer Tip 1. Thoroughly clean the area to be worked on using an angle g

Failure to do so can result in serious injury. Save this manual. Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be

Initial Set Up Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before assembling or making any adjustments to the tool. Note: For additional information regarding the parts listed in the following pages, refer t