Check that lint screen is clean and in place. Load the dryer. • The average load will fill the drum 1/3 to 1/2 full. Items need room to tumble freely for even drying and less wrinkling. Do not overload dryer. • When drying large items, dry only 2 or 3 at a time. Fill out the load with small and medium sized items. • For delicate or very small loads, add 2 lint-free towels for better drying, less wrinkling, and to prevent grease stains caused by fabric softener sheets. • Do not overdry items. Ove

4. To reduce the risk of severe injury or death, follow all installation instructions. TOOLS AND MATERIALS REQUIRED Safety Warning: 1. Before starting installation, make sure that the gas shut off valve is in the off position. 2. All old gas connectors and gas piping should be discarded. ELECTRICAL REQUIREMENTS Electric Dryer: (GDE450AW/CGDE450AW) Circuit Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit breakers. Use separately fused circuits for washers and dryers,

They are on a label Date of purchase in back of the dryer. Staple your receipt to your manual. You will need it to obtain warranty service. English Table Of Contents PAGE SAFETY INSTRUCTIONS....................................................................1 INSTALLATION INSTRUCTIONS ................................................4-12 Tools and Materials Required................................................................4 Electrical Requirements ...........................................

Do not use any phone in your building. 3. Clear the room, building, or area of all occupants. 4. Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. 5. If you cannot reach your gas supplier, call the Fire Department. I nstallations must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the state, province, or region where this appliance is being installed. A WARNING 2 English IMPORTANT SAFETY

This will allow you to remove lightweight items that are dry or other items that you may wish to iron. This feature is available for "Auto Dry" cycles only. 23 English Custom Program: (11) • This allows you to save a favorite cycle,set the desired settings and press "Custom Program"button for 3 seconds. A beep will sound to indicate the cycle has been saved. To recall your custom cycle ,press the "Custom Program"button before drying a load. To change the saved cycle,set the desired settings

Note: If drying rack is not in place, rolling inner tub could collide with drying rack and causes damage to the dryer and drying rack. AUTO DRY CYCLE 1.Press any button except "Off" button to power on. • Turn on the power switch, the computer board beeps once and the dryer transfers from off status to the initial operating status (Normal program). • If no "Start/Pause" button is pressed in 5 min after powering on, it automatically cuts off power and returns to off status. • It returns to off sta

Do not reach into the appliance if the drum is moving. 6. Do not install or store this appliance where it will be exposed to water And/or to the weather. 7. Do not tamper with controls. 8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-repair instructions that you understand and have skills to carry out. 9. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softe

6. Attach the white (neutral) power cord conductors to the outer cord and the green ground wire from the dryer harness to the brass-colored center terminal on the terminal block. Tighten the screw securely. 7. Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block. Warning: Do not make a sharp bend or crimp wiring /conductor at connections. 8. Tighten the screws securing the cord restraint firmly against the power cord. 9. Tighten the strain rel

4. Press “Timed Dry” button to set the required drying time; Press “Temp” button to set the required drying temperature. In “Touch Up” cycle only a 20 minutes Timed Dry can be selected. Temp in “Touch Up” cycle is High Medium Low. Temp in “Gentle Dry” cycle is low only. 5. When starting the machine close the door first, then press the “Start/Pause” button. If a pause is needed during drying, press this button. Pressing again will resume operation. 6. Regardless of the dryer status (drying, pause

If being installed in a manufactured (mobile) home,the dryer MUST employ a 4-conductor power supply cord. NEMA 14-30 type SRDT or ST (as required) rated at 240 Volt AC Minimum, 30 Amp., with 4 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. See Electrical Connections for A 4-Wire System. Canada Only Candian models are supplied with the appropriate power cord. Unpacking Your Dryer 1. Remove all packaging material. This includes th