Votes - 4, Average rating: 4 ( )

Manafacture: Kenmore File size: 4.22 mb File name: Language of manual:

Reinstalling the door 1. Check for fingerprints on the glass. Clean the glass if necessary. 2. Place the inner door assembly into the outer door assembly. Align the hinge cover and hinge in the openings on each side. A. Hinge screws To fit correctly, the inside door assembly edge is completely B. Hole screw plugs inside the outside door assembly edge. 3. Reassemble the inner and outer door assemblies with the 5. Move hinge to the other side and reattach with the 4 screws 6 screws. removed in Step 3. 6. Reverse the plastic cover. Slide it up over the inner door assembly edge and gently snap into place. 7. Set the inner door assembly aside. 4= Use a small flat-blade screwdriver to remove plug strip from the door opening. Slide the head of the screwdriver under the top portion of the plug strip, being certain not to scratch the dryer surface. Lift up. Repeat in the middle and at the bottom. Remove the plug strip in the door opening and insert in the opposite side. 5= Insert a screw in the 2nd opening from the top of the hinge opening and partially tighten. Hang the door by placing the top hinge keyhole over the 2nd screw head and tighten the screw. By putting this screw in first, the door will hang in place while you insert and tighten the remaining 4 screws. A. Dryer door B. Dryer C. Insert this screw first 6. Close the door and check that it latches securely. 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check the dryer's final location. Be sure the vent is not crushed or kinked. 5. Check that the dryer is level. See "Level Dryer." 6. For power supply cord installation, plug into an outlet. For direct wire installation, turn on power. 7. Remove the blue protective film on the console and any tape remaining on the dryer. 8. Read "Dryer Use" in the Dryer User Instructions. 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 10. Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: • Controls are set in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into an outlet and/or electrical supply is on. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door. If you do not feel heat, turn off the dryer and check the following: • There may be 2 household fuses or circuit breakers for the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician. NOTE: You may notice a burning odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away. DRYER USE AUTO DRY CASUAL DELICATE MANUAL ESIIMAIEO OPTUONS MODURERS @ HIGH DA _IP0 0 MORE NORMAL SIATUSwEoCOOL DOWN 0 © CYCLES MEDIUM HIGH 0 LESS @ MEDIUM WRIKLE6UARD0 ... @ LOW @ HIGH AUTO DRY CEC_Erlf SC_E_4o LEVEL DAMP DRY SIGNAL CONIRO[ LOCKEOO RESS&HOI)3s_{o [1 0 0CK/ UNLOCK CONTROl BULKY/ BEDDIN HEAVY DUlY ALIO/YCIISONtY_ _ EXTRALOW @ LOW • AIR DRY @ OFF WRINKLE GUARD TEMPERATURE END of CYCLE SIGNAL [',IA_UALCYCLESONLY; J J Explosion Hazard Fire Hazard Keep flammable materials and vapors, such as No washer can completely remove oil. gasoline, away from dryer. Do not dry anything that has ever had any type of oil on Do not dry anything that has ever had anything it ({ncmuding cooking oils). flammable on it (even after washing). Items containing foam, rubber, or plastic must be dried Failure to follow these instructions can result in death, on a cmothesHne or by using an Air Cycme. explosion, or fire. Failure to follow these instructions can result in death or fire. WARNING: To reduce the risk of fire, electric shock, or injury to To make changes during an Auto Dry Cycle: persons, read the IMPORTANT SAFETY INSTRUCTIONS before Adjust Options. operating this appliance. NOTE: Auto Dry Level selections can be made only while Follow these basic steps to start your dryer. Please refer to using Auto Dry Cycles. You can select a different dryness level, depending on your load, by pressing Auto Dry Level specific sections of this manual for more detailed information. and choosing More or Less. Selecting More or Less 1. Clean lint screen before each load. See "Cleaning the Lint automatically adjusts the sensed time needed. Screen." @ MORE 2. Place laundry in dryer and shut door. @ 3. Press the selected cycle pad. The preset settings for Auto Dry @ LESS Cycles or Manual Cycles will glow. The estimated or actual cycle time (in minutes) will show in the display. C) AUTO DRY To use an Auto Dry Cycle LEVEL PRESS & HOLD 3 • Select an Aut...

Download now

Please, enter two numbers from picture: