Votes - 3, Average rating: 3.7 ( )

Manafacture: Speed Queen File size: 703.49 kb File name: Language of manual:

LOADING DOOR SWITCH SWITCH COUPLER T275IE1A Figure 31 CYLINDER DOOR STRIKE The door strike must be adjusted to have sufficient tension to hold loading door closed against force of load tumbling against it. Proper adjustment is when 8 to 15 pounds (35.6 N - 66.7 N) pull is required to open door. To adjust, open door, loosen jamnut and turn door strike screw in or out as required. Retighten jamnut. T048IE1A DOOR STRIKE DOOR LATCH ACORN NUT Figure 32 M412616 55 56 M412616 DRIVE V-BELT To reduce the risk of serious injury or death, disconnect power to the tumbler before performing this operation. WARNING 2. To adjust belt tension, loosen adjusting bolt holding idler housing assembly to housing support. 3. To tighten V-belt: a. Loosen lower nut on adjusting bolt. b. Turn bolt up until belt has proper tension. c. Tighten upper and lower nut or adjusting bolt. 4. To loosen V-belt: a. Loosen top nut on adjusting bolt. b. Turn bolt down until belt has proper tension. c. Tighten upper and lower nut or adjusting bolt. 5. Replace guard on rear of tumbler. 6. Upper belt requires no adjustment since it is selfadjusting. Proper tension is when belt can be depressed approximately ... inch (1.27 cm) by applying light thumb pressure at a point midway between the sheave and motor pulley. 1. Remove guard from rear of tumbler. To reduce the risk of serious injury or death, guard MUST be installed on rear of tumbler after belt adjustment is made. WARNING Figure 33 T278IE3A POLY V-BELT (Poly V-belt is self-adjusting) IDLER HOUSING ASSEMBLY DRIVE V-BELT IDLER HOUSING BOLTS (2) ADJUSTING BOLT SECTION IV Preventive Maintenance Instructions DAILY 1. Make certain drying cycle has ended. 6. Ensure lint screen covers entire opening in lint screen hood. Gaps between lint screen and lint 2. Open loading door. screen hood allows lint to flow into ductwork system restricting air circulation. 3. Unlock and remove lint panel. 7. Wipe any accumulated lint off thermostat 4. Remove accumulated lint in lint compartment. sensing probe. Lint buildup on sensing probe will Lint left in lint compartment will be drawn back cause overheating of tumbler. onto lint screen and restrict air circulation. 8. Replace and securely lock lint panel. 5. Clean lint from lint screen. If lint screen is torn replace immediately. A torn lint screen allows lint to flow into ductwork system restricting air circulation. WARNING T046IE3A THERMOSTAT SENSING PROBE LINT SCREEN Figure 34 MONTHLY 1. Perform daily cleaning of accumulated lint. 6. Remove bottom cover from vertical exhaust duct and clean out all accumulated lint. 2. Deactivate electrical circuit by turning off electrical disconnect switch on rear of tumbler. 7. Reinstall vertical exhaust duct cover. 4. Remove exhaust duct from rear of tumbler and 8. Inspect entire duct work assembly and clean out clean out all accumulated lint. all accumulated lint. 5. Reinstall exhaust duct. 9. Energize electrical circuit to tumbler by turning on electrical disconnect switch on rear of tumbler. M412616 57 Quarterly 1. Deactivate electrical circuit by turning off disconnect switch on rear of tumbler. 2. Perform daily cleaning of accumulated lint. 3. Perform monthly inspection and cleaning of accumulated lint. 4. Clean accumulated lint and other debris from front and back motor air vents. 5. Shut off gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be at 900 angle to gas supply line when in “OFF” position. Biannually 1. Deactivate electrical circuit by turning off disconnect switch on rear of tumbler. 2. Perform daily cleaning of accumulated lint. 3. Perform monthly inspection and cleaning of accumulated lint. 4. Perform quarterly inspection and cleaning of accumulated lint. 5. Remove or open all panels and check accessible bolts, nuts, screws, terminals and fittings for tightness. 6. Shut off gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be at 900 angle to gas supply line when in “OFF” position. 7...

Download now

Please, enter two numbers from picture: