Anote estos números en las líneas de abajo y guárdelos para su referencia en el futuro. Número de modelo ____________________ Tipo ___________ Número de serie _________ Número de parte 893885-007 NORMAS DE SEGURIDAD IMPORTANTES ADVERTENCIA: Cuando use herramientas neumáticas siempre debe seguir las precauciones básicas de seguridad para reducir el riesgo de herida personal, incluyendo lo siguiente: LEA Y SIGA TODAS LAS INSTRUCCIONES. Hay ciertas aplicaciones para las cuales esta herramie

14). CAUTION: times. Keep tool pointed away from yourself and others at all Always connect tool to air supply before loading fasteners. Do not load fasteners with trigger or safety depressed. Always wear Z87.1 approved safety glasses, and hearing protection when preparing or operating the tool. Never use a tool that leaks air or . needs repair. ■ ■ 2. Depress latch (B) Fig. 15, open feeder cover and swing open magazine cover (see Fig. 16). 3. Adjust nail support (C) Fig. 16, for desire

Do not use liquid lubricants on this tool. CLEAN AND INSPECT DAILY CAUTION: Remove fuel cell and purge tool before cleaning and inspection. Correct all problems before placing the tool back in use. EXTERIOR Wipe tool clean and inspect for wear or damage. If necessary, use a solution of warm water and dish washing detergent to wipe exterior of tool only. DO NOT SOAK tool with cleaning solution. Do not use solvents on tool, this can damage internal parts. Do not use oil or grease on this too

Make sure all screws and caps are securely tightened. 5. NEVER USE TOOL IF trigger or compression mechanism are inoperable, missing or damaged. Do not alter or remove trigger or other components. Make daily inspections for free movement of trigger and compression mechanism. Do not use tool if trigger can be pulled without tool being fully compressed. 6. DO NOT USE TOOL WITHOUT SAFETY WARNING LABEL. If label is missing, damaged or unreadable, contact your Porter-Cable Service Center for a repla

Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair. The depth that a fastener is driven is controlled by the pressure of the air supply. The amount of pressure required will vary depending on the size of the fastener being used and the material being fastened. Experiment with the air pressure setting to determine the best pressure for th

plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. __^_ Type ........................ Serial No._. ................................................. ...................................................................................................;..................... Part No. 883794-699 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using pneumatic tools, basic safety precautions should always be followed to

For a replacement trigger or to order a bump action trigger contact your authorized service center or call 1-888-848-5175. tO ReplACe seqUentiAl tRiGGeR (ns100B only) Trigger Removal (Fig. 2) 1. Lock off trigger. 2. Remove air from the tool. 3. Remove rubber grommet (N) from end of dowel pin (M). 4. Remove dowel pin. 5. Remove trigger assembly from trigger cavity under the handle of the tool housing. Trigger Installation 1. Insert the trigger kit into trigger cavity. 2. Ensure that trigger sprin

1. To drive the fastener shallower, rotate the depth setting wheel (L) to the right. 2. To drive a fastener deeper, rotate the depth setting wheel (L) to the left. CLEARING A JAMMED FASTENER Lock off trigger, disconnect air line from tool and remove fasteners from magazine before making adjustments or personal injury may result. Keep the tool pointed away from yourself and others. Serious personal injury may result. 1. Lock off trigger (NS100B only). 2. Disconnect air supply from tool. 3. Push t

When the switch is in the unlocked position, the tool will be fully operational. The trigger should always be locked off whenever any adjustments are made or when tool is not in use. LOADING THE TOOL (FIG. 3) Keep the tool pointed away from yourself and others. Serious personal injury may result. Never load fasteners with the contact trip or trigger activated. Personal injury may result. Disconnect tool from air supply before removing or re-installing no-mar pad. 1. Read all Safety Warnings befo

REpAIRSFor assistance with your tool, visit our website at for a list of service centers, or call the PORTER-CABLE Customer Care Center at (888) 848-5175. SERvICEREpLACEMENTpARTSUse only identical replacement parts. For a parts list or to order parts, visit our website at servicenet. porter-cable.com. You can also order parts from your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer Care Center at (888) 848-5175. SERvI