Votes - 3, Average rating: 3.3 ( )

Manafacture: Humax File size: 395.57 kb File name: Language of manual:

Select Installation and press the OK button. 3. Select Status and press the OK button. STB Status You can confirm the information of the STB. Signal Detection You can display the percentage of signal strength and quality. Humax SW Update You can update software automatically or manually. When completing the software update, the product is automatically powered off and again. Note: To perform software update, you will be prompted to enter your PIN-Code. Enter the PIN-Code using the NUMERIC(0~9) buttons. Irdeto SW Update When OTA is available, Irdeto SW Update is activated. Conditional Access You can check the information of the conditional access components. Mail Message You can receive mail sent by the broadcasting company. !. 6 #. . You can restore the product to the factory default. 1. Press the MENU button. 2. 2. Select Installation and press the OK button. 3. Select Default Setting and press the OK button. 4. Enter your PIN-Code. 5. When default setting is completed, the installation wizard pops up automatically and assists channel search. . . $5 ) $5 ) In order to maintain proper performance of the product, it is essential to have the most up-to-date software. Visit the Humax website to check the latest news and newly released software versions. – It is recommended that you periodically check for the availability of software update. $. 30. 732. . /. OTA, an abbreviation of Over–the-Air, is a standard for the transmission of software through a broadcast system. OTA is simply an alternative method for downloading software versions. However, the manufacturers reserve the right for deciding the release of the software for their products by beaming the latest software versions over the air via satellite. Note that OTA is only limited to certain geographical regions mainly due to different antennas having different footprints(area where the signal can be received). The software update via satellite will only occur under the following circumstances. 1. The equipment should have appropriate loader software. Caution: • Please note that if normal loader software is not equipped, the product may not be updated or operate properly after software update. 2. The manufacturer decides to release the software via a designated satellite. 3. The equipment must be tuned properly to the same antenna equivalent to that of the manufacturer. 4. Update software when the signal strength and quality is high. If the weather is not favorable, and the signal strength and quality are not recommendable, perform the software update later. Caution: • Please be careful to keep the power on and the power cord plugged in during software update. If the power is off during software update, fatal damage may be caused to the product. • Please be careful not to pull out the signal line (LNB cable) during software update. Update may be interrupted and the product may not operate. Caution: • It may take 5 ~10 minutes to update software. • Other functions will not activate while software update takes place. • You cannot schedule recording during software update.The installation wizard pops up automatically and assists channel search. . . $5 ) $5 ) $. 5 . ) . . . You can connect your product to the PC directly and update your software by transferring the new software from the PC. Follow these steps to download new software from PC to this product. 1. Download the new software file equivalent for this product model from the Humax website (2. Download and install the download tool. 3. Connect your PC to this product with an RS-232C serial cable. 4. Execute the installed download tool and follow the instructions provided. 5. Power On/Off to start operating. . . %/)).%/)). %. 09#. . Before contacting your local service centre, please read the tips below carefully. If the problem persists after completing the following procedure, please contact your local product distributor or service centre for further instructions. 1. No message displayed on the front panel. (The product will not switch on.) • Check the main power cable and make sure it is plugged into a suitable power outlet. • Check that the mains supply is switched on. • Check that the power switch is on at the rear of the product. (where applicable) • Connect the power cable to a different power outlet. 2. No picture on TV set • Make sure that the product is powered on and in operation mode. (Press the STANDBY button) • Make sure that the AV cable is firmly connected to the TV. • Make sure that the antenna cable is properly connected to the product. • Make sure that the antenna setting in the menu is correct. • Check the brightness level of the TV. • Check if the channel is currently on air. Contact the broadcaster to ensure that the channel is running. 3. Poor picture/sound quality • Install the antenna in an obstacle-free place. • Make sure there is no mobile phone or microwave oven near the product. • Keep the power and the a...

Download now

Please, enter two numbers from picture: