Votes - 3, Average rating: 4
(
)
)
|
manual abstract
RSVP also features a removable and rechargeable, ultra-thin, Nickel-Metal- Hydride cellular battery. RSVP slides onto the back of your phone in place of the existing battery unit, providing the control and convenience of a pager and a phone in a single unit. RSVP allows you to manage your cellular phone traffic, return calls at your convenience, screen calls, extend phone battery life, and even remain accessible while your phone is turned off. Paging Features Summary: . Eight numeric message slots . Displays time of day . Message time stamping . Programmable alarm . Retains messages while turned off and when replacing battery Battery Features Summary: . Fits any Motorola MicroTAC or retail pocket personal cellular telephone . Powerful and environmentally friendly Nickel-Metal-Hydride battery USING THIS GUIDE . 12-digit numeric display . Backlit display . Musical alert . Vibrate or audible mode with reminder alert . Battery is detachable from pager unit . Spare batteries are small enough to carry in a shirt pocket . One hour talk time, eight hours standby This user’s guide describes the following: l l How to remove your cellular phone’s existing battery Set up and operate your pager l l Maintain your RSVP pager in top operating condition Use the RSVP cellular battery and optional charger adapter 2 PROCEDURE FOR CONNECTING YOUR NEW RSVP PAGER TO YOUR CELLULAR PHONE Remove battery from any Motorola MicroTAC or retail pocket personal cellular telephone in the following manner: t Slide battery downward against stop ¬ Press and hold down battery release t t ® Lift battery off cellular phone Note: Ensure the Nickel-Metal-Hydride battery is fully charged and installed in the RSVP pager before performing this procedure. Install your RSVP pager in place of the cellular phone battery in the following manner: . Set RSVP onto mounting ¬ slide approximately Position RSVP one inch below with display battery release end toward phone antenna ® Slide RSVP up until pager snaps into place PAGING SERVICE ACTIVATION Paging service providers require certain procedures for activating your RSVP pager. Contact your service provider to activate paging service. On/Read/ Select Button (W) Button Display On/Read/ Select Button (W) Button Display CONTROLS AND DISPLAY INDICATORS The locations and descriptions of the RSVP pager controls and display indicators are shown below: Alert/Backlight Indicator Backlight/Reset Button (l ) Menu/Lock (X) Battery Charger/ Programmer Contacts Pager Display: Message Alarm Lock Indicator 10:47a[ \ = B Indicator Alert Continuing Mode Time Message Indicator of Day Indicator 12:48p1: Message Slot Message Time Number Stamp TURNING YOUR PAGER ON Press W to turn your pager on.Your pager will alert indicating that it is on. The time of day and the “Alert Mode” indicator, silent ([) or audible (D), is displayed. READING MESSAGES The RSVP pager can receive up to eight 20-character messages. When a message is received, the pager alerts with an audible or a vibrate alert, and a flashing alert indication. Press any button to stop the alert. Display your message as follows: 1. Press the W button to display your message. Messages that contain more than 12 characters are continued on a second screen. The (B) indicator means a second screen exists. 2. Press W to advance to the second screen. If not selected, the second screen is automatically displayed after one minute. The last screen of your message displays the message slot number and the time the message was received. If a message is left unread, the pager emits a reminder alert every two minutes, and the number of unread messages is displayed. 3. The pager automatically returns to the main status display after approximately eight seconds. TURNING ON THE BACKLIGHT In low light conditions, press l on the display backlight. Press l again to turn off backlight or allow it to turn off automatically. RESET Pressing the l button twice always resets the pager back to the main display menu. CHANGING ALERT MODES 1. Press X. Either “Silent?” or “Audio?” is displayed, depending on the current mode. 2. To change the alert mode, press W. For your pager to vibrate, it must be in the “silent” mode. TURNING YOUR PAGER OFF 1. Press X until the “PAGER OFF?” prompt is displayed. 2. Press W to turn the pager off. With the pager off, the clock is shown on the display, but not the “Alert Mode” indicator. SETTING THE ALARM Your pager’s alarm can be set to alert you to a certain time of day. Set the alarm as follows: 1. Press X until “SET ALARM?” appears on your display. 2. Press W to select alarm on/off sequence. 3. To move to the next digit, press W. To advance through each digit, press X. Repeat this process for each field (On/Off, hours, minutes, AM/PM). 4. Press W to turn the alarm on or off. 5. Press the l button twice to return to the main display menu. The \ indicator appears on the display when the alarm is turned on. At the selected time, the alarm vibrates or emits a unique 20-...
Why do I have multiple icons popping up on my home screen even after removing them of a little blue android guy with letters underneath it PSB
Why do I have multiple icons popping up on my home screen even after removing them of a little blue android guy with letters underneath it PSB