Votes - 1, Average rating: 3 ( )

Manafacture: Husqvarna File size: 1.01 mb File name: Language of manual:

Before you start the engine, read this book. A WARNING: Before you make an inspection, adjustment (except carburetor), or repair, disconnect the wire from the spark plug. EMISSIONS CONTROL Maintenance, replacement, or repair of the emissions control devices and systems may be performed by any non-road engine repair establishment or indiv-However, to obtain a "no charge" emissions control service, the work must be performed by a factory authorized dealer. See the Emissions Warranty. GENERAL RECOMMENDATIONS The warranty on this snowthrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the snow thrower as instructed in this manual. ENGINE POWER RATING INFORMATION The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual "on-site" or net power). This difference to due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. 1741506 19 MAINTENANCE AFTER EACH USE • Check for any loose or damaged parts. • Tighten any loose fasteners. • Check and maintain the auger. • Check controls to make sure they are functioning properly. • If any parts are worn or damaged, replace immediately. • Check all safety and instruction decals and labels. Replace any decals or labels that are missing or cannot be clearly read. HOW TO REMOVE THE TOP COVER 1. (Figure 5) Remove the discharge chute (1). 2. Remove the fuel cap. 3. Remove the two nuts and bolts (2) from the front of the top cover (3). 4. Remove the two bolts (4) from the left and right of the top cover (3). 5. Remove the eight screws (5) on the left and right side of the top cover. 6. Remove the three screws (6) from the top portion ofthe control panel. 7. Carefully pull the rear of the top cover (4) up and over the gas tank. 8. To install the top cover (4), reverse the above steps. LUBRICATION BEFORE STORAGE (Figure 5) Lubricate the chute control flange (7). Apply a clinging type of grease such as Lubriplate. 3 6 1741506 20 MAINTENANCE HOW TO ADJUST THE AUGER CONTROL CABLE The auger control is adjusted at the factory. During normal use, the auger control cable can become stretched and the auger drive lever will not properly engage or disengage the auger. 1. (Figure 6) Remove the"Z" hook (1) from the auger drive lever (2). 2. (Figure 7) Slide the cable boot (1) off the cable adjustment bracket (2). 3. Push the bottom of the auger control cable (3) through the cable adjustment bracket (2) until the"Z" hook (6) can be removed. 4. Remove the"Z" hook (4) from the cable adjustment bracket (2). Move the"Z" hook (4) down to the next adjustment hole. 5. Pull the auger control cable (3) up through the cable adjustment bracket (2). 6. Put the cable boot (1) over the cable adjustment bracket (2). 7. (Figure 6) Install the"Z" hook (1) to the auger drive lever (2). 8. To check the adjustment, start the snowthrower. Make sure the auger does not rotate when the auger drive is released. HOW TO REMOVE THE BELT COVER 1. (Figure 8) If equipped, remove the heat shield (1) from the rear of the belt cover (2). 2. Remove the four bolts and nuts (3) holding the belt cover (2) to the auger housing. 3. Remove the one screw (4) holding the belt cover (2) to the bottom cover (5). 4. To remove, hold the bottom portion of the belt cover (2) and pull down and out. 5. To install the belt cover (2), reverse the above steps. 1741506 21 MAINTENANCE Figure 8 HOW TO REPLACE THE DRIVE BELT The drive belt is of special construction and must be replaced with original factory replacement belt available from your nearest authorized service center. 1. Remove the belt cover. See "How To Remove The Belt Cover" 2. (Figure 9) Remove the drive belt (1) from the idler pulley (2). 3. Move the belt guide (4) away from the drive belt (1). 4. To reduce pressure on the drive belt (1), move the idler pulley (2) away from the drive belt (1). Rem...

Download now

Please, enter two numbers from picture: