Votes - 2, Average rating: 5 ( )

Manafacture: Husqvarna File size: 1.01 mb File name: HOUS2007_O0707902.pdf Language of manual:

Guide the snowthrower by moving the handle (10) either left or right. Do not attempt to push the snowthrower. 3. To stop, release the auger drive lever (4). NOTE: If the auger continues to rotate, see "How To Adjust The Auger Control Cable” in the Maintenance section. 1741506 15 OPERATION BEFORE STARTING THE ENGINE 1. Before you service or start the engine, familiarize yourself with the snow thrower. Be sure you understand the function and location of all controls. 2. Make sure that all fasteners are tight. 3. Make sure the fuel tank is filled with fresh, clean fuel. 4. Before starting the engine, make sure all controls operate correctly. HOW TO STOP THE ENGINE To stop the engine, turn the ignition key to the OFF position. Keep the ignition key in a safe place. The engine will not start without the ignition key. HOW TO START A COLD ENGINE 1. Fill the fuel tank with fresh, clean fuel. See "Add Fuel To The Engine” in the Assembly section. 2. Move the choke control to FULL position. 3. (Figure 3) Make sure the auger drive lever (4) is in the disengaged (released) position. 4. Insert the ignition key (6) and turn to the ON position. 5. Move the choke control (11) to the full choke position. 6. (Electric Start) Connect the power cord to the switch box (9) located on the engine. 7. (Electric Start) Plug the other end of the power cord into a three-hole, grounded 120 volt AC receptacle. (See the WARNING in this section.) HOW TO START THE ENGINE NOTE: An electric starter kit can be added to recoil start engines. Electric starter kits are available from your nearest authorized service center. A WARNING: The starter is equipped with a three-wire power cord and plug and is designed to operate on 120 AC household current. Carefully follow all instructions in the “How To Start The Engine” section. To connect a 120 volt AC power cord, always connect the power cord to the switch box first. Then, plug the other end into the three-hole grounded receptacle. When disconnecting the power cord, always unplug the end from the three-hole grounded receptacle first. 8. Push the primer button (7) two times. Every time you push the primer button (7), wait two seconds. 9. (Electric Start) Push on the electric start button (8) until the engine starts. Do not crank for more than 10 seconds at a time.The electric starter is thermally protected. If the electric starter overheats, it will automatically stop and can be restarted when it has cooled to a safe temperature. A wait of about 5 to 10 minutes is required to allow the electric starter to cool. 10. (Recoil Start) Rapidly pull the recoil starter handle (10). Do not allow the recoil starter handle (10) to snap back. Slowly return the recoil starter handle (10). 11. If the engine does not start in 5 or 6 tries, see the “Troubleshooting Chart” instructions. 12. (Electric Start) When the engine starts, release the electric start button (8) and move the choke control (14) to 1/2 choke position. When the engine runs smoothly, move the choke control (11) to the OFF position. 1741506 16 OPERATION 13. (Electric Start) First disconnect the power cord from the three-hole receptacle. Then, disconnect the power cord from the switch box (9). NOTE: In temperatures below 0° F, allow the engine to warm up for several minutes before blowing snow. A WARNING: Never run the engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and colorless deadly gas. Keep hands, feet, hair, and loose clothing away from any moving parts located on the engine or the snow thrower. The temperature of muffler and nearby areas may exceed 150° F. Avoid these areas. HOW TO START A WARM ENGINE (Figure 3) If an engine has been running and is still warm, leave the choke control (11) in the OFF position and do not push the primer button (7). If the engine fails to start, follow the instructions "How To Start A Cold Engine.” NOTE: Do not use the primer button (7) to start a warm engine. HOW TO START A WARM ENGINE WITH A FROZEN STARTER If the electric starter is frozen and will not turn the engine, follow the instructions below. 1. (Figure 3) Pull out the recoil starter handle (10) as far as possible. 2. Quickly release the recoil starter handle (10) to snap back against the recoil starter. If the engine still fails to start, repeat the two previous steps until the engine starts. Then, continue with the directions "How To Start A Cold Engine.” To help prevent the possible freeze-up of the recoil starter and of the engine controls, proceed as follows after each snow removal job. 1. With the engine running, quickly pull the recoil starter handle (10) three or four times with a continuous full arm stroke. This will produce a loud clattering sound that is not harmful to the engine or starter. 2. Stop the engine. Wipe all snow and moisture from the carburetor cover, control levers, and cables. Also move the choke control (11) and recoil sta...

Download now

Please, enter two numbers from picture: