091-0058 SNAPPER * 1189 Old Schuylkill Road * P.O. Box 111 * Parker Ford, PA 19457-0111 PHONE: (215) 495-7181 * * * FAX: (215) 495-5951 Form SLB862 693 LEAF BLOWER OWNER’S MANUAL Assembly Instructions Your leaf blower has been carefully packed at the factory. Before proceeding with assembly, make sure all parts have been received and are in good condition. If there are shortages or damage, report it immediately to the company from whom you obtained the machine. (Note: In the following In

Hinge & Deflector (Deflector Removed for Clarity) D. Tapered Spacer E. Original Lockwasher and Nut F. 5/8 x 1 Cylinder Spacer A BC Figure 7. Connect Deflector Spring A. Spring Anchor B. Spring C. Deflector Arm 6 7 54”Turbo Blower Installation Instructions FRONT Install Turbo Blower 1. Install the turbo blower assembly. Insert the tapered spacers (B, Figure 8) through the bottom of the blower housing (A). 2. Install one spring clip (C) on both tapered spacers (B). 3. Hook the bottom of the turbo

Do not put any objects like sticks or fingers in holes of impeller cover. 4. Stop the engine and disconnect the spark plug wire before attempting to clean obstructions or blockage from the intake or discharge passages. 5. Stop the engine and allow it to cool for at least two minutes before refilling the gas tank or before lifting leaf blower. 6. Do not put a vacuum kit of any kind on this machine. Foreign objects entering the impeller housing will destroy the impeller and may cause injury. M

• Attach lower portion of handle assembly to engine base by aligning holes in lower handles with corresponding holes in engine base. Fasten with four 5/16-18 x 1-1/2” bolts and secure with serrated flange nuts. Tighten all handle assembly bolts securely. +1" 0 -1" 1 Assembly complete. Your unit is now ready to be started and checked for proper operation. Some minor final adjustments may be required; see the Maintenance portion of this manual. 4 unit operation STARTING THE ENGINE IMPORTANT NOTE:

(Includes Items 44 thru 54) LINE, Fuel GROMMET, Fuel Line CUP, Fuel Line FILTER ASS'Y, Fuel (Includes items 48, 49, 64, 65, 66, 68) CLIP SLEEVE, Gov CAP ASS’Y, (Includes Items 51 thru 54) CAP, Fuel GASKET HOLDER VALVE, Breather MOUNT, Fan-Wheei SCREW, M5x12mm PHCR (3) MOUNTING PLATE, Engine DAMPER,Eng.Mtg.Plate(4) PAD, Fuel Tank(4) SEAL, Eng. Mtg. Plate (3) BRACKET SWITCH, Stop SCREW FELT (2) RING SCREEN SCREW BODY, Fuel Filter ENGINE, COMPLETE(lncludes items 2 thru 42 & 61, 62, 6

• Never attempt to make major repairs on this unit unless you have been properly trained. Improper service procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty. 4 3 unit assembly Note: Please refer to Parts List for correct part identification and placement. FRONT WHEEL ASSEMBLY • Attach left and right caster brackets to caster wheel using 3/8-18 x 2-1/4 bolt and lock nut. Insert bolt through hole in bracket. Place caster wheel onto bolt. Place ot

TWIN LINE TAP FEED HEAD KIT ITEM PART NO. DESCRIPTION _ 6-8037 KIT, .095 L.H. Twin Line Tap Feed Head (Includes Items 1 thru 7) 1 4-2081 HEAD, Twin Line Bump, L.H. (Includes Items 2 thru 6) 2 4-2073 ASSEMBLY, Hub 3 4-2074 SPRING 4 4-2082 ASSEMBLY, Spool & Line 5 2-1971 KNOB, Bump 6 4-2083 BOLT, Slotted Hex Flange, L.H. 7 1-8784 CARD/Parts (Not Illustrated) 1 5 Section I - TRIMMER ACCESSORIES BRUSH BLADE CONVERSION KIT WITH METAL SHIELD 16 Section I - TRIMMER ACCESSORIES BRUSH BLAD

Be sure all safety features are attached, adjusted properly and functioning properly. • Never operate with the discharge deflectors removed or altered. • Do not change the engine governor setting or over speed the engine. • Stop on level ground, shut off engine before leaving the operator’s position for any reason. • Stop equipment and inspect impeller blades after striking objects or abnormal vibration occurs. Make necessary repairs before resuming operations. • Keep hands and feet away intake

Make sure the blower end is directed away from people, animals, glass, and solid objects. - -- For Parts Call K&T 606-678-9623 or 606-561-4983 BlowerVacuumSTARTINGPOSITION WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property,

Note that there are three holes in each side of the upper handle. These are height adjustment holes. Position the upper handle at a comfortable height for you (usually waist high). Move the upper handle up or down slightly to align the hole in the upper handle and lower handle. Locate the upper lifting handle (item 4) and with the hardware provided, bolt through the upper lifting handle, lower and upper handle. Tighten securely. 3. Attach the throttle control to the upper handle as per the draw