Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 1   File size: 799 kb   Manafacture: MTD  
Category: Blower systems
@name@name@name

54th Street, Chandler, Arizona 85226 or if in Canada call 1-800-668-1238. No product returned directly to the factory will be accepted unless prior written permission has been extended by the Customer Service Department of MTD SOUTHWEST INC. This limited warranty does not provide coverage in the following cases: A. Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts B. MTD does not extend any warranty for products sold or exported outside

downloaded: 25   File size: 2 mb   Manafacture: MTD  
Category: Blower systems
@name@name@name@name@name@name

The tubes and guards are in place and secure. • Always hold the unit with both hands when operating. Keep a firm grip on both the front and rear handle or grips. • To reduce the risk of hearing loss associated with sound level(s), the use of hearing protection is required. •Watch out for children, pets, open windows, or freshly washed cars, and blow debris away. • After using blowers and other equipment, clean up. Dispose of debris in trash receptacles. OPERATING AS A BLOWER 1. Start engine. See

downloaded: 11   File size: 679 kb   Manafacture: MTD  
Category: Blower systems
@name

BOX 368022 • CLEVELAND, OHIO 44136-9722 FORM NO. 770-96-7D Models 685 and 689 7D — Page 2 Models 685 and 689 PARTS LIST FOR MODELS 685 AND 689 POWER VACUUMS REF. NO. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 05778B Clutch Grip Ass’y. 43 - Engine 2 711-0679 Clevis Pin .375" Dia. x 1.88" 751-0581 Muffler Guard Ass’y. (Incl. 3 747-0154 Clutch Rod 32" Lg. Hardware)tt 4 749-0787 Handle Brace 46 748-0201 Spacer .63" I.D. x .88" O.D. x 5 — Part of Engine .

downloaded: 0   File size: 713 kb   Manafacture: MTD  
Category: Blower systems
@name

Do not let starter handle snap back against starter. 6. Repeat instructions 4 and 5 until engine fires. When engine starts, move choke control gradually to RUN position. 4 TO STOP ENGINE 1. To stop engine, move throttle control lever to OFF position. 2. Disconnect spark plug wire and ground to prevent accidental starting while equipment is unattended. ADJUSTMENTS A WARNING: Do not at any time make any adjustment to the unit without first stopping engine and disconnecting spark plug wire.

downloaded: 2   File size: 528 kb   Manafacture: MTD  
Category: Blower systems
@name

and Mfg. Code which appear on your unit in the space below. You must have these numbers, along with the date of purchase, in order to receive warranty or service. MEETS ANSI SAFETY STANDARDS MODEL NO. MFG. CODE Made ^ in AMERICA WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or st

downloaded: 0   File size: 1 mb   Manafacture: MTD  
Category: Blower systems
@name@name

Attaching NOTE: The blower/vacuum tube comes unassembled on this unit. Installation is required to provide safe and easy use for the operator. WARNING: To prevent serious personal injury, stop the engine, disconnect the spark plug wire and allow the impeller to stop before attaching or removing tubes. 1. Remove the screws and nuts provided from the hardware pack. 2. Insert the blower/vacuum tube all the way into the opening on the motor housing until the holes in the tabs on the blower/vacuum tu

downloaded: 1   File size: 214 kb   Manafacture: MTD  
Category: Blower systems
@name

Carburetor Repair Kit (Walbro) * 791-182521 Gasket Diaphragm Repair Kit (Walbro) * 791-180530 Piston Ring 791-182498 Short Block Assembly (includes 8-10 & 23-27) * 791-610309 Oil Seal * Not Shown Issued 5/03 HOUSING PARTS - MODEL 340BV- 2-CYCLE GAS BLOWER / BLOWER-VAC PPN 41BS340G034 -® Item Part No. Description 1 791-182465 Handle Grip Assembly (includes 2-5) 2 791-182466 Vibration Dampner 3 791-182467 Dampner Spacer 4 791-182468 Handle Screw 5 791-182469 Screw 6 791-182470 Di

downloaded: 8   File size: 234 kb   Manafacture: MTD  
Category: Blower systems

downloaded: 1   File size: 749 kb   Manafacture: MTD  
Category: Blower systems
@name

NO. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 749-0784 Upper Handle 21 710-0170 Hex Locking Bolt 5/16-24 x 2 726-0100 Push Nut 3/8" Rod .64" Lg. 3 720-0171 Crank Knob 22 736-0162 FI-Wash. (692 Only) 4 736-0117 FI-Wash. .385” I.D. x .62" 23 736-0300 FI-Wash. .38“ I.D. x .57" 5 714-0114 Sq. Key 1/4" x 2.0" Lg.* 24 750-0528 Spacer .382" I.D. x .50" 6 710-0442 Hex Bolt 5/16-18 x 1.50“ Lg.* x .180" Lg. 7 16453 Engine Mounting Frame Ass’y. 25 736-0169 L-Wa

downloaded: 0   File size: 749 kb   Manafacture: MTD  
Category: Blower systems
@name

.344" I.D. x 1.12 5" O.D. .75" Lg. 8 14479 Directional Discharge Ass y. 23 14539 Housing—Engine Brace Ass’y. 9 14562B Nozzle Ass’y. (Black) 24 728-0173 Pop Rivet (5 Required) 731-1123 Nozzle Ass’y. (Beige) 25 14569 Wiper Retaining Strip 10 14563 Nozzle Plate Ass’y. 26 735-0214 Nozzle Wiper 11 712-0267 Hex Nut 5/16-18 Thd.* 28 710-0602 Hex Bolt 5/16-18 x 1.00" Lg.*tt 12 736-0119 L-Wash. 5/16" I.D.* 29 710-0255 Truss Mach. Scr. 1/4-20 x .75"f+ 13 710-0191 Hex Bolt 3/8-24 x





Category