Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 3   File size: 460 kb   Manafacture: Billy Goat  
Category: Blower systems
@name

Always follow mix ratio found on stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor. 16.5 HANDLING & TRANSPORTING: STORAGE 16.4 Be sure engine has come to a complete stop before removing or emptying bag!! This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings page 2-3). Many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. However, f

downloaded: 9   File size: 1 mb   Manafacture: Billy Goat  
Category: Blower systems
@name

· Check engine. Engine will not start. · Engine not in full choke position. · Out of gasoline or bad, old gasoline. · Spark Plug wire disconnected. · Gas valve off. · Dirty air cleaner. · Check choke position. · Check gasoline. · Connect spark plug wire. · Turn on gas valve. · Clean or replace air cleaner. Contact a qualified service person. Engine is locked, will not pull over. · Engine problem . · Contact an engine servicing dealer for engine problem s. When servicing engine refer to specific

downloaded: 0   File size: 1 mb   Manafacture: Billy Goat  
Category: Blower systems
@name

Your BILLY GOAT ® FORCE Blower was shipped in one carton, completely assembled except for the Upper Handle Assembly and Front Diverter. Mounting hardware for the Upper Handle Assembly can be found in the parts bag. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the unit by cables. PUT OIL IN ENGINE BEFORE STARTING PARTS BAG & LITERATURE ASSY Warranty card P/N-400972, Owner’s Manual P/N-440021, Declaration o

downloaded: 0   File size: 730 kb   Manafacture: Billy Goat  
Category: Blower systems
@name

Tests were performed on 5-25-2006 under the conditions listed below. General Conditions: Sunny Temperature: 72.32oF(22.4oC) Wind Speed: 3.8 mph (6.12kph) Wind Direction: East Humidity: 62.2% Barometric Pressure: 29.9Hg (101.3kpa) INTENDED USE INTENDED USE: This machine is designed for removing thatch from your lawn, renovation of existing lawns, and to assist in overseeding operations. The machine should not be used for any other purpose than that stated above. Do not operate if excessive vibrat

downloaded: 9   File size: 31 kb   Manafacture: Billy Goat  
Category: Blower systems
@name

Set the air compressor to 30 - 100 working PSI. Do NOT exceed 110 PSI. 3. Squeeze Air Blow Gun trigger to begin the flow of air. 4. Release Air Blow Gun trigger to stop the flow of air. 5. When finished, turn off the air compressor and then disconnect Air Blow Gun from the air source hose 6. Only use clean and dry compressed air. Never use oxygen, carbon dioxide, combustible gases or any other bottled gas as a power source. 92363 951 59 For technical questions and replacement parts, pleas

downloaded: 0   File size: 3 mb   Manafacture: Billy Goat  
Category: Blower systems
@name

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. PRODUCT SPECIFICATIONS Construction Injection molded polypropylene plastic housing and tube blower Fan blower type Totally enclosed fan cooled white polypropelene fan Motor Unit 110-120 Volts AC, 60 Hz Motor Power Peak2100 Watts, 20.8 Amps Power Speed Control Dial Con





Category