Login:
Votes - , Average rating: ( )

User manual American Standard, model 1662

Manafacture: American Standard
File size: 710.76 kb
File name: Install_2275.pdf

Language of manual:en

The document is loading, please wait
The document is loading, please wait

manual abstract


M968637 Rev 1.4 Electric Drill 6mm (15/64") Drill Bit Phillips Screwdriver Pencil 1660.225 1660.236 65mm (2-1/2") 127mm (5") 900mm (35-3/8") 82mm (3-1/4") 70mm (2-3/4") 25mm (1") 45mm (1-3/4") 849mm (33-3/8") 86mm (3-3/8") 65mm (2-1/2") 86mm (3-3/8") FINISHED FLOOR OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 915mm (36") 1525mm (60") TO Hammer SHOWER SYSTEM KITS 1662 SERIES 1660.505 1660.500 1660.502 1498mm (59") 32mm 13mm (1-1/4") (1/2") 1/2" NPT RUBBER GASKET FINISHED WALL 1/2" NPSM HOSE CONNECTION 53mm (2-1/16") (48" - 60") (OPTIONAL) TO FINISHED FLOOR Turn off hot and cold water INSTALL WALL SUPPLY CAUTION supplies before beginning. 1/2" NPT APPLY SEALANT OR TEFLON TAPE 1 Supply to WALL SUPPLY (1) is 1/2" NPT. See rough-in above for detailed information. Install RUBBER SEAL (2) onto WALL SUPPLY (1). Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY (1) onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL (2) should be tight against finished wall. 2 1 146mm (5-3/4") 67mm (2-5/8") 1/2" NPSM 1/2" NPSM 1/2" NPSM 240mm (9-1/2") 85mm (3-3/8") 1/2" NPSM 240mm (9-1/2") 85mm (3-3/8") 1660.550 250mm (9-7/8") 42mm (1-5/8") 57mm (2-1/4") 120mm (4-3/4") 1660.843 1660.143 1660.743 1/2" NPSM 266mm (10-1/2") 116mm (4-5/8") 122mm (4-3/4") 1/2" NPSM 1/2" NPSM 1/2" NPSM 265mm (10-3/8") 115mm (4-1/2") 122mm (4-3/4") 1/2" NPSM 258mm (10-1/8") 121mm (4-3/4") 98mm (3-7/8") 76mm (3") 252mm (9-7/8") 239mm (9-3/8") 94mm (3-3/4") 81mm (3-1/4") 247mm (9-3/4") 94mm (3-3/4") 1660.628 1660.638 1/2" NPSM 90mm (3-1/2") 65mm (2-1/2") 1660.741 191mm (7-1/2") 24mm (1") A950646 600mm (23-5/8") 549mm (21-5/8") 2 M968637 Rev 1.4 INSTALL LOWER SUPPORT BRACKET INSTALL SLIDE BAR LOCATE UPPER MOUNTING BRACKET INSTALL UPPER MOUNTING BRACKET The SLIDE BAR works best when secured to the wall studs or cross brace using the WOOD SCREWS. If a mounting into the studs is not possible, use appropriate wall fasteners to provide secure installation. Mark a vertical center line in the location you wish to install the SLIDE BAR. NOTE: The height from the finished floor is optional. See rough-in drawing for suggested dimensions. Determine desired height from the finished floor to the lower support and mark a horizontal center line. Place the MOUNTING BRACKET (1) on the center lines, with a pencil mark the location on the mounting holes to be drilled. Fig. A. Using 15/64" diameter drill. Drill two mounting holes 1" max. deep. Fig. B. Install the bottom of SLIDE BAR (3) into the MOUNTING BRACKET (2). IMPORTANT: The slot at the bottom of the slide bar must face toward the wall. Rotate the slide bar until it locks into place and cannot be turned. Fig. B. Install the two ANCHORS (2) provided into the mounting holes. (Use a hammer to lightly tap ANCHORS (2) into place.) Make sure they are installed flush with the finished wall. Place the MOUNTING BRACKET (1) over the ANCHORS (2) and secure the MOUNTING BRACKET (1) with the SCREWS (3) provided. Fig. C. 3 Slide the COVER (1) onto the MOUNTING BRACKET (2) flush against the wall. Fig. A. Install the upper MOUNTING BRACKET (1) onto the SLIDE BAR (2). Align the MOUNTING BRACKET (1) with center lines and mark the center mounting hole with a pencil as shown. Fig. A. Remove the SLIDE BAR (2) and set a side. Using 15/64" diameter drill bit, drill mounting hole 1" max. deep. Fig. B. Slide the COVER (4) onto the MOUNTING BRACKET (2) flush against the wall. Install the ANCHOR (1) provided into the mounting hole. Make sure it is installed flush with the finished wall. (Use a hammer to lightly tap ANCHOR (1) into place.) Place the MOUNTING BRACKET (2) over the ANCHOR (1) and secure the MOUNTING BRACKET (2) with the SCREW (3) provided. NOTE: Do not tighten fully. Slide the MOUNTING BRACKET (2) up against the bottom of the mounting slot.. 4 5 OPTIONAL TO FINISHED FLOOR FINISHED FLOOR SLOT BOTTOM OF MOUNTING SLOT VERTICAL C/L HORZ. C/L Fig. A Fig. B Fig. C 3 3 2 1 1 2 2 2 2 2 1 1 3 4 1 Fig. B Fig. B Fig. B Fig. A Fig. A Fig. A M968637 Rev 1.4 INSTALL SLIDE BAR INTO MOUNTING BRACKETS FINISH INSTALLATION 6 7 Install the SLIDE BAR (1) back into the lower MOUNTING BRACKET (2). IMPORTANT: The slot at the bottom of the slide bar must face toward the wall. Rotate the slide bar until it locks into place and cannot be turned. Fig. A. Push top COVER (3) and MOUNTING BRACKET (4) down onto top of SLIDE BAR (1). Fig. A. Tighten MOUNTING SCREW (5) with phillips screw driver to secure assembly to wall. Fig. B Repeat above steps to snap the lower ESCUTCHEON andSPACER (4) into place. Align the ESCUTCHEON and SPACER so that the spacer is sitting on the ESCUTCHEON. Rotate the upper ESCUTCHEON and SPACER (1) on SLIDE BAR (2) until the three snap arms align with the holes in the cover. Push ESCUTCHEON and SPACER (1) into COVER (3) until it snaps in place. SLIDE BAR TOP Fig. A Fig. B 5 1 1 1 3 3 2 2 2 4 4 5 6 3, 4 CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A...

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category