Votes - 2, Average rating: 4
(
)
)
|
manual abstract
See also the "Toolless cap with grip" section in the Safety Precautions. Opening the threaded filler cap N Turn the cap counterclockwise until it can be removed from the tank opening. N Remove the filler cap. Refueling Take care not to spill fuel while fueling and do not overfill the tank. STIHL recommends use of the STIHL filling system (special accessory). 249BA054 KN 249BA053 KN 002BA419 KN 249BA056 KN 249BA055 KN 200BA421 KN English Closing the threaded filler cap 200BA422 KN N Position cap. N Turn the cap clockwise as far as it will go and tighten it as securely as possible by hand. Chain Lubricant For automatic and reliable lubrication of the chain and guide bar – use only an environmentally compatible quality chain and bar lubricant. Rapidly biodegradable STIHL Bioplus is recommended. Biological chain oil must be resistant to aging (e.g. STIHL Bioplus) since it will otherwise quickly turn to resin. This results in hard deposits that are difficult to remove, especially in the area of the chain drive and chain. It may even cause the oil pump to seize. The service life of the chain and guide bar depends on the quality of the lubricant. It is therefore essential to use only a specially formulated chain lubricant. Do not use waste oil. Renewed contact with waste oil can cause skin cancer. Moreover, waste oil is environmentally harmful. Waste oil does not have the necessary lubricating properties and is unsuitable for chain lubrication. Filling Chain Oil Tank A full chain oil tank is sufficient for only half a tankful of fuel. Check the oil level regularly during cutting work. Never allow the oil tank to run dry. Preparations 390BA047 KN NThoroughly clean the oil filler cap and the area around it to ensure that no dirt falls into the tank. N Position the machine so that the filler cap is facing up. HT 100, HT 101, HT 130, HT 131 English Opening the filler cap 402BA036 KN The bayonet-type oil tank filler cap with hinged grip can be opened and closed without tools. N To open the tank, swing the grip to the vertical position. N Turn the filler cap counterclockwise as far as stop and remove. Filling up with chain oil N Filling up with chain oil Take care not to spill chain oil while refilling and do not overfill the tank. Closing the filler cap 402BA037 KN N To close the oil tank, place the filler cap in position with the grip upright, making sure the recesses are in alignment. N Turn the filler cap clockwise as far as stop. N Fold the grip down so that it is flush with the top of the cap. If the oil level in the tank does not go down, the reason may be a fault in the oil supply system: Check chain lubrication, clean the oilways, contact your dealer for assistance if necessary STIHL recommends that you have servicing and repair work carried out exclusively by an authorized STIHL servicing dealer. Checking ChainLubrication 390BA048 KN The saw chain must always throw off a small amount of oil. Never operate your saw without chain lubrication. If the chain runs dry, the whole cutting attachment will be irretrievably damaged within a very short time. Always check chain lubrication and the oil level in the tank before starting work. Every new chain has to be broken in for about 2 to 3 minutes. After breaking in the chain, check chain tension and adjust if necessary – see "Checking Chain Tension". HT 100, HT 101, HT 130, HT 131 English Adjusting the Telescoping Fitting the HarnessShaft The type and style of the harness HT 101, HT 131 only depend on the market. Always shut off the engine and fit Shoulder strap the chain guard 390BA049 KN NLoosen the screw. NAdjust shaft to the required length. NTighten down the screw firmly. 2 1 390BA040 KN NPut on the shoulder strap (1). NAdjust the length of the strap. NWith the power tool attached, the carabiner (2) must be at about the same height as your right hip. Full harness (HT 100, HT 101 only) 386BA012 KN 2 1 3 N Put on the full harness (1) and sling (2) as described in the instruction sheet provided. N Adjust the harness and thigh strap (3) as required. N Rest the powerhead in the sling during cutting work. HT 100, HT 101, HT 130, HT 131 HT 100, HT 101, HT 130, HT 131 English 24 HT 100, HT 130 only N Put the backpack carrying system (1) on your back and adjust it as described in the instruction sheet provided. N Attach the carabiner (2) to the machine's carrying ring. N Attach the pole pruner to the carrying strap when cutting. N Adjust the hip belt (3), both shoulder straps (4) and the carrying strap (5). HT 101, HT 131 only N Put the backpack carrying system (1) on your back and adjust it as described in the instruction sheet provided. N Secure the sliding adjuster (2) to the shaft. N Attach the pole pruner to the carrying strap when cutting. Backpack Carrying System 246BA015 KN 1 2 246BA016 KN 4 5 3 246BA010 KN 1 2 N Adjust the hip belt (3), both shoulder straps (4) and the carrying strap (5). 246BA011 KN 453246BA011 KN 453 246BA012 KN NSqueeze the grips to move the sl...
Other models in this manual:Garden Tools - STIHL HT 100 (2.33 mb)
Garden Tools - STIHL HT 101 (2.33 mb)
Garden Tools - STIHL HT 130 (2.33 mb)
Garden Tools - STIHL HT 131 (2.33 mb)