Votes - 4, Average rating: 4.8 ( )

Manafacture: MTD File size: 2.68 mb File name: Language of manual:

Do not spill gasoline on hot engine. MTD PRODUCTS INC 5389 WEST 130th STREET P.O. BOX 2741 CLEVELAND OHIO 44111 FORM NO. 770-3844 I 192-766 Tiller Attachment is for 10, 12, and 14 HP Tractors built before 1971. 193-966 Tiller Attachment is for the 1971 through 1973 10, 14, 15 and 16 HP Tractors. (Models 141-760, 141-960, 142-760, 142-960, 143-860 and 143-960). 193-967 Tiller Attachment is for the Hydrostatic Tractors. (Model 141-900, 142,990 and 143-990). ASSEMBLY INSTRUCTIONS FOR MODELS 193-966 and 193-967. (Refer to Fig. 2) 1. Assemble outer tine assemblies complete to the inner tine assemblies complete with four spirol pins 5/16 diameter x 2-1/2” long Heavy Duty. (Ref. 28). 2. Assemble pivot bracket assembly (Ref. 24) to the power input side of the gear case with two bolts 5/8-11 x 1-1/2” long (Ref. 67) and lockwashers 5/8 diameter (Ref. 25). 3. Assemble other pivot bracket assembly (Ref. 24) to the right hand side of gear case. 4. Assemble the universal drive shaft assembly (Ref. 26). To the gear case with spirol pin (Ref. 22). Drive pin into the shaft with a hammer. The end of the universal drive shaft assembly with the square head set screw attaches to the power take off on tractor. 5. Assemble cover bracket (Ref. 20) to cover bracket assembly (Ref. 5) with one carriage bolt 1-1/2” long (Ref. 15). 6. Assemble cover bracket assembly (Ref. 5) to cover assembly (Ref. l)with six carriage bolts 5/16—18x1” long (Ref. 4) lockwashers 5/16 diameter (Ref. 6) and nuts 5/16-18 thread (Ref. 7). Assemble bolts and nuts loose until all six are started, then tighten. 7. Assemble cover and bracket assembly to gear case with four bolts 1/2—13 x 7/8 long. (Ref. 9) and lockwashers 1/2 diameter (Ref. 10). Assemble bolts loose until- all four are started, then tighten. 8. Remove the solid pipe plug in the hole above the input shaft in the gear case and replace it with the vented pipe plug (Ref. 21). Refer to Figure 2 for proper location of the vented plug. This vented plug allows the gear case to breathe. 9. The lubricant level in the gear case should be checked after it is attached to the tractor. ASSEMBLY INSTRUCTIONS FOR MODEL 192-766. (Refer to Figs. 1 and 2) 1. Assemble outer tine assemblies complete to the inner tine assemblies complete with four spirol pins 5/16 diameter x 2-1/2” long Heavy Duty. (Ref. 28). 2. Assemble flat bracket L.H. (Ref. 69) to the power input side of the gear case with two bolts 5/8—11 x 1-1/2” long (Ref. 67) and lockwashers 5/8 diameter (Ref. 25). 3. Assemble offset bracket R.H. (Ref. 68) to the right hand side of the gear case with two bolts 5/8-11 x 1-1/2” long (Ref. 67) and lockwashers 5/8 diameter (Ref. 25). 4. Assemble the universal drive shaft assembly (Ref. 26) to the gear case with spirol pin (Ref. 22). Drive pin into the shaft with a hammer. The end of the universal drive shaft assembly with the square head set screw attaches to the power take off on the tractor. 5. Assemble cover bracket (Ref. 5) to the cover assembly (Ref. l)with sixcarriage bolts 5/16—18x1” long (Ref. 4), lockwashers 5/16 diameter (Ref. 6) and nuts 5/16—18 thread (Ref. 7). Assemble bolts and nuts loose until all six are started, then tighten. 6. Assemble cover and bracket assembly to the gear case with four bolts 1/2—13 x 7/8 long (Ref. 9) and lockwashers 1/2 diameter (Ref. 10). Assemble bolts loose until all four are started, then tighten. 7. Remove the solid pipe plug in the hole above the input shaft in the gear case and replace it with the vented pipe plug (Ref. 21). Refer to Figure 2 for proper location of the vented plug. This vented plug allows the gear case to breathe. 8. The lubricant level in the gear case should be checked after it is attached to the tractor. 2 ATTACHING YOUR ROTARY tlLLER TO YOUR TRACTOR (Models 193-966 and 193-967) 1. Before attaching your rotary tiller to your tractor, be sure the rear wheels on the tractor are all the way into the minimum rear wheel width. Refer to your tractor manual. 2. Remove the draw bar assembly from the three point hitch of your tractor by removing the two cotter-hairpins. 3. Place the rotary tiller behind the tractor in the approximate position shown in Fig. 2. 4. Attach universal drive shaft (Ref. 26) to the tractor power take off. Tighten set screw (Ref. 27). 5. Move the lift lever on the tractor until the draft bar assemblies line up with pivot brackets (Ref. 24). 6. Assemble pivot brackets (Ref. 24) to the rear of the tractor with washers and cotter-hairpins. ATTACHING YOUR ROTARY TILLER TO YOUR TRACTOR (Model 192-766). 1. Before attaching your rotary tiller to your tractor, be sure the rear wheels on the tractor are all the way into the minimum rear wheel width. Refer to your tractor manual. 2. Remove the “U” part of the plow hitch from your tractor by removing the two cotter-hairpins on the loose clevis pins and the two cotter-hairpins from the hitch adjusting rods. Refer to Fig. 1. 3. Adjust the hitch adjusting r...

Download now

Please, enter two numbers from picture: