Votes - 2, Average rating: 4 ( )

Manafacture: MTD File size: 2.68 mb File name: 12b5a2c9-2564-4a2e-8c0f-6d64cdf08034.pdf Language of manual:

This CANNOT be accomplished in one pass. Maximum tilling depth may be only 2-1/2” on extremely hard soil on the first pass. The more passes you make with the tiller over the same area, the deeper you can till and the finer you pulverize the soil. Change directions as often as you can to level out the ground and to prevent furrows. When tilling, the tiller will push the tractor and the transmission on the tractor will hold the tractor back. For easy lifting of the rotary tiller from the ground, shut off the power by disengaging the PTO handle and continue to drive the tractor forward. The tines will climb out of the hole when you pull the lift lever handle back. LUBRICATION Gear Case - Lubricated with three quarts of SAE 140 oil. It is lubricated at the factory. Be sure to check the lubricant level before each use. To check the oil level, remove plug (Ref. 61) on the side of the gear case. See Fig. 3. Lubricant should be at this level. If not, fill through the vented pipe plug hole (Ref. 21) until it overflows through the hole in the side of the gear case. Replace both plugs. BE SURE THE VENTED PIPE PLUG IS IN THE OIL FILL HOLE. Grease Fittings — There are three grease fittings on the universal drive shaft assembly. Lubricate after each 25 hours of use with an automotive multi-purpose type grease. Apply grease with grease gun provided with your tractor. Lubricate until the old grease is pushed through and clean grease appears. 3 ROTARY TILLER 192-766, 193-966 and 193-967 FIG. 3 Oil level should be checked when the tiller is mounted on the tractor with the tines touching the ground. Place a 6 inch block under the front of the case to check oil level with the tiller off the tractor. I PARTS LIST FOR TILLER ATTACHMENT MODELS 192-766, 193-966 and 193-967 Ref. No. Part No. Color Code DESCRIPTION Ref. No. Part No. Color Code DESCRIPTION 1 9844A Cover Assembly 34 721-110 Oil Seal 1-1/4 I.D. x 2.004 O.D. 2 714-111 Cotter Pin 3/32 Dia. x 1" Lg.* 35 742-126 Needle Bearing 1-1/4 I.D.x 1.625 O.D. 3 9846 Cover Flap Assembly 36 748-159 Thrust Bearing 4 710-276 Carriage Bolt 5/16—18 x 1" Lg. * 37 716-116 Truarc Snap Ring No.5100-125 5 10981 Cover Bracket Assembly 38 717-148 Sprocket - 25 Teeth 6 736-119 Spring Lockwasher 5/16 Scr. * 39 713-119 Chain w/master Link No. 60 x 39 lg. 7 712-267 Hex Nut 5/16-18 Thread * 40 741-127 Needle Bearing 1.25 I.D. x 1.625 O.D. 8 9850 Rod 41 741-130 Thrust - Race 1.25 I.D. x 1.23 9 710-365 Hex Hd.Cap Scr. 1/2-13 x 7/8" Lg.* 42 741-128 Thrust Bearing 1.25 I.D. x 1.927 O.D. 10 736-921 Spring Lockwasher 1/2—13 Thread * 43 741-129 Thrust - Race 1.25 I.D. x .030 11 712-267 Hex Nut 5/16-18 Thread * 44 717-146 Worm Wheel 12 742-110 Tine R.H. Slasher 45 717-147 Sprocket 13 Teeth 13 742-113 Tine L.H. Slasher 46 714-125 Square Key 5/16 x 1-1/4 Lg. * 14 10502 Extension - Tine 47 714-124 Square Key 5/16 x 1-3/4 Lg. * 15 710-431 Carriage Bolt 3/8—16 x 1-1 /2"Lg.* 48 711-325 Worm Gear Shaft 16 712-711 Hex Nut 3/8-24 Thread * 49 715-108 Spirol Pin 1/4 x 1" Lg. 17 736-169 Spring Lockwasher 3/8 Scr. * 50 741-107 Timken Roller Bearing 3/4" Bore 18 710-113 Hex Hd.Cap Scr.3/8—24 x 1-5/8" Lg.* 51 711-329 Spacer 19 10501 Mounting Tine 52 717-145 Worm 20 10984 Cover Bracket (966 and 967 only) 53 711-328 Spacer 21 737-102 Square Hd. Pipe Plug w/Vent 3/8 Thd. 54 714-314 Key Hi Pro No.HP 505 3/4" * 22 715-118 Spirol Pin 5/16 x 1-3/4" Lg. * 55 711-324 Worm Shaft 23 712-798 Hex Nut 3/8-16 Thread * 56 721-108 Gasket - Worm 24 10982 Pivot Bracket Assembly 57 711-327 Case Cover (966 and 967 only) 58 736-329 Spring Lockwasher 1/4" Scr. * 25 736-158 Spring Lockwasher 5/8 Scr. * 59 710-206 Hex Hd.Cap Scr. 1/4-20 x 7/8"Lg. * 26 717-149 Universal Drive Shaft Assembly 60 721-111 Oil Seal 3/4 I.D. x 1.503 O.D. (766 and 966 only) 61 737-103 Square Hd. Pipe Plug 3/8 Thread * 717-184 Universal Drive Shaft Assembly 62 721-107 Gasket - Gear Case (967 only) 63 710-380 Hex Hd. Cap Scr.5/16-18 x 1-3/4" Lg.* 27 710-357 Square Hd.Set Scr.3/8-16 x 1/2" Lg.* 64 719-146 Tiller Gear Case - R.H. 28 715-113 Spirol Pin 5/16"Dia.x 2-1/2"Lg. 65 711-497 Clevis Pin (966 and 967 only) Heavy Duty 66 712-923 Hex Locknut 5/8—18 Thread * 29 714-123 Square Key 5/16 x 2" Lg. * 67 710-367 Hex Hd. Cap Scr.5/8-11 x 1-1/2"Lg. 30 711-451 Shaft 68 9841 Bracket - L.H. (Not xhown 31 719-145 Tiller Gear Case - L.H. For 192-766 only) 32 736-124 Felt Dust Pad - Small 69 9842 Bracket-R.H. For 192-766 only) 33 721-109 Oil Seal 1-1/4 I.D. x 2.004 O.D. 70 11566 Input Shaft Seal * For faster service obtain standard nutsf bolts and washers locally. If these items cannot be obtained locally, order by part number and size as shown on the parts list. NOTE: Parts shown on drawings that do not have reference numbers are tractor parts. Refer to your tractor manual. 6 ASSEMBLY INSTRUCTIONS FOR BOOSTER SPRINGS 732-246 (USED WITH TILLER ...

Download now

Please, enter two numbers from picture: