Votes - 2, Average rating: 3.5 ( )

Manafacture: Tanaka File size: 598.68 kb File name: Language of manual:

• Empty the fuel tank before storing the unit/machine. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Store unit/machine out of the reach of children. • Clean the unit carefully and store it in a dry place. • Make sure engine switch is off when transporting or storing. • When transporting in a vehicle, cover chain with chain cover. If situations occur which are not covered in this manual, take care and use good judgment. Contact your dealer if you need assistance. Pay special attention to statements preceded by the following words: WARNING! Indicates a strong possibility of severe personal injury or loss of life, if instructions are not followed. CAUTION! Indicates a possibility of personal injury or equipment damage, if instructions are not followed. NOTE! Helpful information for correct function and use. 3 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN 3. Assembly procedures Drive shaft to engine (Fig. 1 -1) Loosen tube locking bolt (1) about ten turns so that the bolt point will not obstruct drive shaft tube to be inserted. When inserting drive shaft tube, hold the tube locking bolt outward preventing inside fitting from obstructing as well. Insert the drive shaft into the clutch case of the engine properly until the marked position (2) on the drive shaft tube meets the clutch case. NOTE! When it is hard to insert drive shaft up to the marked position on the drive shaft tube, turn drive shaft by the cutter mounting end clockwise or counterclockwise. Tighten tube locking bolt lining up the hole in the shaft tube. Then tighten clamp bolt securely (3). Cutting attachment to drive shaft (Fig. 1-2) Loosen tube locking bolt (1). Insert the drive shaft into the gear case of the attachment properly until the marked position (2) on the drive shaft tube meets the gear case. NOTE! When it is hard to insert drive shaft up to the marked position on the drive shaft tube, turn attachment clockwise or counterclockwise. Tighten tube locking bolt lining up the hole in the shaft tube. Then tighten clamp bolt securely (3). Installation of handle (Fig. 1-3) Attach the handle to the drive shaft tube with the angle towards the engine. Adjust the location to the most comfortable position before operation. Throttle wire/stop cord Remove air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig.1 -5) Connect throttle wire end to carburetor. (Fig. 1 -6) Cover throttle wire and stop cords together with protective tube provided up to air cleaner cover. (Fig. 1 -7) 4 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN WARNING! TPS-2501,TPS-2510.TPS-250PN,TPS-270PN WARNING! Never try to start engine without side case securely fastened. NOTE! When assembling brand new unit, take off and discard the cardboard (1) between gear case and side case. (Fig. 1 -8A) Installation of bar and chain 1. Remove chain bar clamp nut (2). 2. Remove the side case (1). (Fig. 1 -8) 3. Install, the chain bar (1) onto the bolt (2), then push it toward the sprocket (3) as far as it will go. Make sure that the boss of chain tension adjusting bolt (4) fits into the hole of the bar (5). (Fig. 1-9) NOTE! Slightly move the bar back and forth and make sure the chain tension boss (4) fits into the hole (5) in the bar properly. 4. Confirm the direction of saw chain (1) is correct as in the figure, and align the chain on the sprocket. (Fig. 1 -10) 5. Guide the chain drive links into the bar groove all around the bar. 6. Install the side case (2) onto the guide bar clamp bolt. Then fix the clamp nut (3) temporarily. (Fig. 1 -10) 7. Raise the bar end, and tighten the chain (1) by turning the tension adjustment bolt (2) clockwise. To check proper tension, lightly lift up the center of chain and there should be about 0.5-l.0mm clearance between bar and edge of drive link (3). (Fig. 1-11, 12) CAUTION! PROPER TENSION IS EXTREMELY IMPORTANT! (Fig. 1-11, 12) 8. Raise the bar end and securely tighten the chain bar clamp nut with the box wrench. (Fig. 1 -11) 9. A new chain will stretch so adjust the chain after a few cuts and watch chain tension carefully for the first half hour of cutting. NOTE! Check the chain tension frequently for optimum performance and durability. CAUTION! When the chain is excessively tightened the bar and chain will be damaged rapidly. Conversely, when the chain is excessively loosened, it may get out of the groove in the bar. Always wear gloves when touching the chain. WARNING! During operation, hold the unit firmly with both hands. A single hand operation may cause serious injury. 5 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed wit...

Download now

Please, enter two numbers from picture: