Votes - 2, Average rating: 4
(
)
)
|
manual abstract
SELECT DVD Remote sensor To operate Set TV / DVD·VIDEO to the DVD player DVD·VIDEO, then press SELECT DVD and point at the remote sensor at the DVD-VCR the VCR DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor at the DVD-VCR your TV TV and point at the remote sensor at your TV Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one. • Do not use different types of batteries. • Do not leave the remote commander in an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a malfunction. Setting up the remote commander Controlling other TVs with the remote commander The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number. 1 Set TV / DVD·VIDEO at the top of the remote commander to TV. 2 Hold down ?/1, and enter your TV’s code number using the number buttons. Then release ?/1. Now you can use the ?/1, VOL +/–, CH +/–, MUTING*, TV/VIDEO and ENTER* buttons to control your TV. You can also use the buttons marked with a dot (•) to control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to DVD·VIDEO. * for Sony TV only Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. TV brand Code number Sony 01 Akai 04 AOC 04 Centurion 12 Coronado 03 Curtis-Mathes 12 Daewoo 22 Daytron 12 Emerson 03, 04, 14 Fisher 11 General Electric 06, 10 LG/Gold Star 03, 04, 17 Hitachi 02, 03 J.C.Penney 04, 12 JVC 09 KMC 03 Magnavox 03, 08, 12 Marantz 04, 13 MGA/Mitsubishi 04, 12, 13, 17 NEC 04, 12 TV brand Code number Panasonic 06, 19 Philco 03, 04 Philips 08 Pioneer 16 Portland 03 Quasar 06, 18 Radio Shack 05, 14 RCA 04, 10 Sampo 12 Sanyo 11 Scott 12 Sears 07, 10, 11 Sharp 03, 05, 18 Sylvania 08, 12 Teknika 03, 08, 14 Toshiba 07 Wards 03, 04, 12 Yorx 12 Zenith 15 Getting Started continued 11 Setting up the remote commander Notes • If you enter a new code number, the code number previously entered will be erased. • If the TV uses a different remote control system from the one programmed to work with the DVD-VCR, you cannot control your TV with the remote commander. • When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries. Setting up the remote commander Step 3 : Basic hookups Before you get started • Be sure to disconnect the AC power cord of each component before connecting. • Turn off the power to all equipment. • Do not connect the AC power cords until all of the connections are completed. If you connect the AC power cord before the connections are completed, you may not be able to use the Plug and Play function. • Be sure you make connections firmly. Loose connections may cause picture distortion. • If your TV does not match any of the examples provided, see your nearest Sony dealer or qualified technician. Selecting the best hookup option There are many ways in which your DVD-VCR can be hooked up. To hook up your DVD-VCR so that it works best for you, first scan through the table below. Then use the accompanying diagrams and procedures on the following pages to set up your DVD-VCR. If your TV has audio/video inputs, refer to page 14 for audio/video (A/V) hookup. Then follow one of the hookups below. If your TV does not have A/V inputs, go directly to one of the hookups below. If you have Use Refer to Antenna only, no cable TV Hookup 1 (Plug and Play) Pages 15 and 16 No cable box or cable box with only a few scrambled channels Hookup 2 (Plug and Play) Pages 17 and 18 Cable box with many scrambled channels Hookup 3 Page 19 After you have completed the connections, follow the instructions for setup. After you have completed the setup, you are ready to use your DVD-VCR. Procedures differ depending on the hookup you used. Caution Connections between the DVD-VCR’s VHF/UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the DVD-VCR to an antenna or make simultaneous (parallel) antenna and DVD-VCR connections at the antenna terminals of your receiver. Note to CATV system installer (in USA) This reminder is provided to call the CATV system installer’s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connecte...
Other models in this manual:DVD Players - SLV-D560 (1.83 mb)