You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL and ADDITBONAL SAFETY aNSTRUCTIONS carefully 6 -INCH JO/N TER-PL A NER • assembly o operating • repair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A. Part No. 67037 #,_._._ _bS._ general safety instructions 1. KNOW YOUR POWER TOOL Read and understand the owner's manual and labels affixed to the tool. Learn its application and limitations as well as the specific potential hazards p

NUT !i i. •:Q ••• :••• •• know our olnter-maner .... .... P WARNING: F_R" YOUR OWN: SAFETY TURN SWITCH 2 SLIDING GUARD INFEED TABLE SLIDE BRACKET CUTTER GUARD IIII!_1 L I 1 11: DEPTH OF CUT HANDWHEEL. Turning the handwheel counterclockwise Will lower the infeed _ table to maximum depth of 1/8 in, _.. FENCE LOCKS AND STOPS. The fence can be moved across the Jointer to take full advantage of the "sharpness" of the blades. The:fence should be positioned to the extreme right (toward pulley) but not

:/i "< i . '_,/,_ __ _ i_: _i, _ ,///i ...... • ', MODEL NO. ]]3.20680 JOINTER/PLANER ONLY 113.206930 JOINTER!PLANER WITH LEGS AND MOTOR Serial Number ....................................... Model and serial number may be found on a plate attached to your infeed table. You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL and ADDiTiONAL SAFETY iNSTRUCTiONS carefully CRn MaNo 6_-INCH JOIN TER-PLANER ® assembly ® operating o repair parts Sotd by SEARS

2 *T Lockwesher, E.ternaJ 1/4 ................. 2 *U Screw, Pan Hd. 1/4-213 x 1/2 ............... 2 V Jointer-Planer Belt Guard ................. 1 W Attaching Hardware (2 Nuts, 2 Botts) X _lt Guard Clips ........................ 3 Y Belt Guard Support Bracket ............... 1 Z Belt Guard Support ..................... 1 AA Screw Pan Hd. 10-32 x ti2 ................ 2 AB Motor Pulley Belt Guard .................. 1 AC Switch Key ............................ 1 AD Held Dawn/Push Black ...........

You should record both model and code number and retain in a safe place for future use. CALIFORNIA OWNERS: a unique serial code number is stamped on the underside of the machine. CAUTION: Read All Instructions Carefully Before Starting Assembly and Use. Save This Manual For Future Reference. SWAIRS / r.RRFTSMRN® 51_.INCH JOINTER--PLANER • assembly • operating • repair parts SEARS, ROEBUCK AN D CO., Dept. 698/731A, Sears Tower, Ch icago, IL 60684 d_o-15A-oo FULL ONE-YEAR WARRANTY ON .RRFTSMRN, JO

Pressure should be applied over the cutterhead and outfeed table. DO NOT FEED TOO FAST. A slow steady rate of feed produces a smooth accurate cut. Feeding too fast causes a "rippled" cut . . . makes it difficult to guide the workpiece accurately and could be hazardous. PLANING WOOD THAT IS THICKER THAN 3 IN. Always feed WITH THE GRAIN whenever possible. If WITH THE GRAIN the nature of the workpiece is such that it must be fed AGAINST THE GRAIN, take very light cuts and feed slowly, AGAINST THE G

FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY, YOUR UNIT IS EQUIPPED WITH SUCH CONTROLS. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROLS UNDER ANY CIRCUMSTANCES. TRAINING; • Read this operator's manual carefully. Become familiar with the controls and know how to operate your mower properly. Learn how to quickly stop mower, • Do not allow ch