Very easy to use and a must for any chisel owner. It can also be used for plane irons up to 25.8" wide and chisels up to 15.8" wide. If you've tried sharpening blades by hand then you know that this is one tool you must have! Figure 2. g1482 honing guide. H2927—3 Pc. Diamond Whetstone Set Includes extra fine, fine, and coarse grades. Quick, easy and effortless sharpening. no oil lubrication needed. Only requires water. Extremely durable. Figure 3. h2927 3-Pc. diamond Whetstone set. Japanese Wate

Troubleshooting • If the tool chatters, reduce the depth of cut, or try skewing the blade angle. • If the throat clogs with shavings, reduce the depth of cut, or clear larger shavings after each stroke is complete. • If one side of the blade digs into the work- piece more than the other, adjust the blade so it is parallel to the sole. Maintenance • sharpen the blade bevel when it becomes noticeably difficult to push or pull the plane, or when it produces excessive chatter. To learn how to sharpe

Tighten the knurled lock knob to secure the blade. 4. Verify that the blade is parallel with the sole— so an even amount of the blade protrudes from one side to the other. —If the blade is not parallel to the sole, loosen the lock knob and adjust the blade as needed. One side will cut more than the other if the blade is not parallel to the sole. To reduce the risk of injury when using this tool: • Usecarewhenhandlingtheplaneblade. Itissharpandcancauselacerations. • Protectyoureyesfromflyingchips

To achieve the best results when using your specific type of hand plane, we recommend reading books and magazines, and researching the internet. Inventory A. Plane .......................................................... 1 B. Blade .......................................................... 1 C. Frog ............................................................ 1 Setting the Blade 1. Insert the frog beveled-edge down into the throat until it stops on its own or until the groove in the top of the

If you are confused about any aspect of this machine, DO NOT use it until you have answered all your questions. Serious injury may occur. Like all power tools, there is danger associated with the Model G1033 20" Planer. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored serious personal injury may occur. -26-G1033 20" Planer

5. Check your settings one last time and repeat steps 1-4 if necessary. Figure 38. Feed roller height adjustment. Bed Rollers The bed rollers ease stock movement through the planer. The height of the bed rollers will vary depending on the types of wood you will be planing. When planing rough stock, set the rollers slightly high to keep the lumber from dragging along the bed; however, snipe may be unavoidable. Smooth lumber should be planed with the rollers set just above the plane of the table.

Stop tightening it when the drawer side and leg have approximately 3mm of clearance between each other. 6. Position the left side leg (C) on the floor and install the remaining (E4) barrel nuts into cross braces (D, E, & I) (Figure 5), and install cross brace (I) into the right leg. 7. Connect the left leg to cross braces (D, E, & I), and use a 5mm hex wrench to secure the braces to the leg with three (E2) flat washers, and three (E3) barrel bolts, but do not fully tighten at this time. 9. Wi

Depth Of Cut The depth of cut is adjustable. To increase the depth of cut turn the depth control knob (Figure 4) clockwise. To decrease the depth of cut turn the depth control knob counterclockwise. Figure 4. Depth control knob. H3141 Heavy-Duty Planer Depth Stop The final cut depth on rabbeting operations can be set using the adjustable depth stop shown in Figure 6. Loosen the lock lever and slide the depth stop to the desired final depth on the scale. Re-lock the lever to secure the depth stop