Votes - 2, Average rating: 4 ( )

Manafacture: Kenwood File size: 1.27 mb File name: Language of manual:

Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. • You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the “INPUT” indication appears. 3 Use the MULTI CONTROL knob or keys to adjust the input level. • The adjustment mode is displayed for approximately eight seconds. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. 18EN Normal playback Preparing for playback Some preparatory steps are needed before starting playback. AUTO INPUT MODE INPUT SELECTOR (KRF-V5060D/ POWER ON/OFF SPEAKER ON/OFF ON/STANDBY(KRF-V5060D/ V4060D/ V5560D)(VR-605/615) POWER ON/STANDBY V4060D/ V5560D) Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ STANDBY (for VR-605/615) or POWER ON/OFF and ON/ STANDBY (for KRF-V5060D/V4060D/V5560D) key. Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD or DVD/6CH (VR-615/KRF-V5060D only) jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the source to “MD”, follow the steps below: 1 Use the INPUT SELECTOR knob to select “TAPE”. 2 Hold down the AUTO key for more than 2 seconds. • The source indication changes to “MD”. • To return to the original indication, repeat procedure 2. Setting the speaker status The speaker indicator lights up. Press the SPEAKER key to switch the speaker ON or OFF. Listening to a source component INPUT SELECTOR VOLUME CONTROL INPUT SELECTOR VOLUME 1Use the INPUT SELECTOR knob or keys to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob. VR-605/615/KRF-V5060D/V4060D/V5560D 1 “AUX” 2 “TUNER” 3 “CD/DVD” 4 “TAPE” or “MD” 5 “VIDEO1” 6 “VIDEO2” 7 “DVD” or “DVD/6CH” (for VR-615/KRF-V5060D only) KRF-V5060D (for the U.K. and Europe only) 1 “PHONO” 2 “TUNER” 3 “CD/DVD” 4 “TAPE” or “MD” 5 “VIDEO1” 6 “VIDEO2” 7 “DVD/6CH” 2Start playback from the selected source. 3Use the VOLUME CONTROL knob or VOLUME keys to adjust the volume. 19 EN Normal playback Normal playback CINEMA EQ VOLUME CONTROLSPEAKERS ON/OFF PHONES MULTI CONTROL MUTE CINEMA EQ TONE LOUDNESS MULTI CONTROL BASS BOOST MUTE VOLUME Adjusting the TONE (remote control only) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the TONE key to select the TONE mode. 2 Use the MULTI CONTROL knob or keys to select TONE ON/OFF. 3 Press the TONE key for the following displays. 1 TONE : Tone setting mode is ON. 2 BASS : Select this to adjust the low frequency range. 3 TREB : Select this to adjust the high frequency range. 4 Use the MULTI CONTROL knob or keys to adjust the sound quality. • The bass and treble levels are adjustable from -10 to +10 in 2 step increments. • The adjustment item is displayed for approximately 8 seconds. • If CINEMA EQ is turned ON, TONE function will not be available. Once-touch low frequency emphasis (BASS BOOST) (remote control only) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo modes. Press the BASS BOOST key. • Press the key once to select the maximum (+10) low frequency emphasis setting. • TONE will automatically be turned ON. • This key does not function when the receiver is in the sound quality or ambience effects adjustment mode. Switching back the previous setting Press the BASS BOOST key again. Adjusting the LOUDNESS mode (remote control only) You can adjust the Loudness function which controls the low volume settings to maintain the music’s richness. The adjustment can be made when the receiver is in the PCM stereo and analog stereo mode. Press the LOUDNESS key to turn the LOUDNESS setting ON. To cancel Press the LOUDNESS key again so that the “LOUDNESS” indicator goes off. Muting the sound The MUTE key lets you mute the sound of the speakers. Press the MUTE key. To cancel Press the MUTE key again so that the “MUTE” indicator goes off. • MUTE ON can also be deactivated by turning the volume control knob. CINEMA EQ mode You can enjoy a more impressive sound effect when you switch CINEMA EQ ON during Dolby Digital and DTS playback. Press the CINEMA EQ key. “CINEMA EQ” will scroll across the display. • When CINEMA EQ is turned ON, subwoofer remix’s function will also be effective. • If REC MODE is ON or TREBLE’s level is -6 or below, CINEMA EQ function will not be available. To cancel Press the CINEMA EQ key again so that the “CINEMA EQ” indicator goes off and displays “OFF”. • When CINEMA EQ is turned OFF, the setting will remain until the next selection is made. Listening...

Download now

Please, enter two numbers from picture: