The material flow exceeds the atomizing cap capacity. 2. Inlet air pressure is too low. 3. Material is too thick. 1. Lower fluid flow. 2. Increase inlet air pressure. 3. Thin material. Narrow center pat- tern. 1. Volume control turned in too far. 2. Inlet air pressure too high. 3. Fluid pressure is too low. 4. Material is too thin. 1. Increase volume. 2. Reduce inlet air pressure. 3. Increase fluid pressure. 4. Adjust material. No spray output. 1. No pressure at gun. 2. Fluid passages dirty. 3.

Stage two sprays material. 6. Cup: Holds material; includes a vented cap. -10- Model H8115/H8117 Spray Gun SECTION 4: OPERATIONS ADANGER 4 EXPLOSION HAZARD! DO NOT smoke or have any source of flame or spark near spraying. Vapors will explode if ignited. ▲WARNING RESPIRATORY HAZARD! Always use respirator rated for organic vapor and solvent use when using spray equipment. Failure to protect your lungs can lead to respiratory illness and nervous system damage. ▲WARNING TOXIC FUMES! Alway

Build-up of material inside atomizing cap. 1. Clear holes. 2. Clean. 3. Clean. Heavy deposit of material in center. 1. The material flow exceeds the atomizing cap capacity. 2. Inlet air pressure is too low. 3. Material is too thick. 1. Lower fluid flow. 2. Increase inlet air pressure. 3. Thin material. Narrow center pat- tern. 1. Volume control turned in too far. 2. Inlet air pressure too high. 3. Fluid pressure is too low. 4. Material is too thin. 1. Increase volume. 2. Reduce inlet air pressur

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA H5528 & H5529 Parts Diagram REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH5528001 BREATHER PLUG 2 PH5528002 RESERVOIR COVER 3 PH5528003 PLASTIC RESERVOIR 4 PH5529004 ALUMINUM RESERVOIR 5 PH5528005 FILTER 6 PH5528006 FLUID INLET JOINT SEAL 7 PH5528007 FLUID INLET JOINT 8 PH5528008 HANGER 9 PH5528009 FLUID ADJ. NEEDLE 10 PH5528010 FLUI

shutting off air valves. 3. Keep WorK area clean. 7. do not force tool. it will do Cluttered areas and benches invite the job better and safer at the rate accidents. for which it was designed. 4. do not use in dangerous 8. use the right tool. do not environment. do not use pneu-force tool or attachment to do a job matic tools in damp or wet loca-for which it was not designed. tions, or where any flammable or 9. do not use under the noxious fumes may exist. Keep influence of drugs or work area we

150 PSI maximum air pressure. 1.4" NPT. Figure 6. G6261 Campbell Hausfeld™ water filter. G8114—3.8" x 25 Ft. Air Hose G8115—3.8" x 50 Ft. Air Hose G8116—3.8" x 100 Ft. Air Hose Multi-purpose red rubber air hose is flexible and abrasion resistant. Rated for 200 PSI, this air hose has a bursting strength of 800 PSI and 1.4" NPT ends. Figure 7. Red rubber air hose. H7274—Campbell Hausfeld™ Pressure Regulator Provides regulated output pressure of 0 to 125 PSI for proper tool operation. Locking press

shutting off air valves. 3. KEEP WORK AREA CLEAN. 7. DO NOT FORCE TOOL. It will do Cluttered areas and benches invite the job better and safer at the rate accidents. for which it was designed. 4. DO NOT USE IN DANGEROUS 8. USE THE RIGHT TOOL. Do not ENVIRONMENT. Do not use pneu-force tool or attachment to do a job matic tools in damp or wet loca-for which it was not designed. tions, or where any flammable or 9. DO NOT USE UNDER THE noxious fumes may exist. Keep INFLUENCE OF DRUGS OR work area we

parts. Non-slip footwear is recom-20. CHECK DAMAGED PARTS. mended. Wear a protective hair cov-Before further use of the tool, a ering to contain long hair. guard or other part that is dam 12. ALWAYS USE SAFETY GLASSES. aged should be carefully checked Also use a face or dust mask if cut-to determine that it will operate ting operation is dusty. Everyday properly and perform its intended eyeglasses only have impact resis-function. Check for alignment of tant lenses, they are NOT safety moving par