Please retain for future reference. 2 EXPLODED PARTS VIEW 13 14 14 13 Fig.2 12 11 10 9 7 8 4 5 6 2 3 1 A B Fig.1 Fig.3 HV3500 HV2900/ 3900 PARTS LIST FFiigg..11 No.Description Part Code No.Description Part Code 1. Needle and Fluid Tip Tool V0018 7. Fluid Needle 2.0mm V0006 2. Air Cap Ring V0001 8. Lip Seal -Fluid Needle V0007 3. Air Cap V0002 9. Paint Flow Adjuster V0011 4. Spray Direction Plate V0003 10. Paint Container Seal L0682 5. Fluid Tip 2.0mm V0004 11. Pick-up Tube V0012 6. Fluid Tip O-R

2) When you get to the end of the line, release the Trigger for a moment and then apply the product in the opposite direction just beneath the line you have sprayed. 3) Next, to achieve a vertical strip adjust the Spray Direction Plate (4) to the horizontal position then pull the Trigger and move your arm up and down over the horizontal strips you just have sprayed. Through gradual movement of the Spray Direction Plate (4) between Horizontal, Vertical and Round spray pattern you can vary the wid

Please retain for future reference SAFETY OPERATING INSTRUCTIONS PLEASE READ BEFORE USE . ALWAYS CHECK PAINT MANUFACTURERS THINNING INSTRUCTIONS BEFORE PROCEEDING. . ALWAYS CHECK PAINT MANUFACTURER’S INSTRUCTIONS FOR SURFACE PREPARATION. . ENSURE PAINT IS STIRRED THOROUGHLY BEFORE USE. . Never use corroded or damaged batteries, do not mix old and new batteries. . Do not overfill the paint reservoir. . NEVER use any liquids other than those specified. . Always ensure motor housing is firmly clipp

Refer to the chapter on cleaning to see how the Fluid Tip and Fluid Needle can be removed and switched for a smaller/larger Fluid Tip and Fluid Needle assembly. • Fill the Paint Container with the product to be sprayed. Stir well (as mentioned above). • Screw the Paint Container to the base of the Spray Gun and tighten accordingly. • Unroll the motor unit air hose and attach it to the back of the Spray Gun. • Unroll the power cable and attach the plug to the mains supply. • Switch the Spray Stat

The round spray is used for small objects or for areas - such as corners – that are difficult to reach. To adjust the spray pattern, loosen the Air Cap Ring (1), adjust the position of the Air Cap (2) to obtain either a vertical, horizontal or round pattern then re-tighten the aircap ring. PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig.5(a)) Completely close Fluid Adjusting Screw (8) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning th

2. Pour any residual material into its container so that it can be used for the future. 3. Pour a quantity of the respective thinner into Container, shake the gun lightly, reassemble the gun, then spray this liquid through the gun. Repeat this until the thinner being sprayed is coming through with no traces of paint. 4. Clean any traces of paint off the outside of the gun. 5. Clean the Paint Container Seal (12) inside the gun body. 7 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 8 L0553 (04-

Fit the strap hooks into the round holes at the top of the Spray Pack. ii. Feed the strap through the vertical slots at the bottom of the Spray Pack, loop around and feed back through the strap buckle. Spraying IT IS RECOMMENDED THAT THE UNIT IS TESTED WITH WATER PRIOR TO EACH USE 1. Remove Spray Pack Lid (2) and pour in required spray material and thinners. 2. Ensure the spray material and thinners do not exceed the max fill line on the Spray Pack. 3. Fit the Spray Pack Lid, ensuring that Seal

BEFORE USE - PLEASE READ THE SAFETY & OPERATING INSTRUCTIONS. Please retain for future reference N0150 05/05.qxd 27/5/05 10:28 am Page 2 SAFETY INSTRUCTIONS WARNING! FIRE AND EXPLOSION HAZARD. . CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, USE INDOORS ONLY. . The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING US

Earlex Ltd will accept no responsibility for the use of this product if usedfor any other purposes than those detailed herein. SAFETY OPERATING INSTRUCTIONS WARNING: When using the Paint Sprayer, basic safety precautions, including the following, should always be followed t< reduce the risk of fire, electric shock and personal injury ! Keep work area clean -Cluttered areas and benches invite injuries. ! Consider work area environment -Do not expose the spray gun to rain. Do not use the spray gun

BEFORE USE – PLEASE READ THE MANUAL AND SAFETY INSTRUCTIONS. Please retain for future reference MODE D’EMPLOI Merci d’avoir choisi le systeme professionnel de pulverisation de peinture basse pression Earlex. Cet appareil est dote du systeme HVLP (haut volume d’air, basse pression de peinture) extremement polyvalent dont vous pourrez vous servir pour une grande variete d’applications. AVANTTOUTE UTILISATION,VEUILLEZ LIRE CE MANUEL ET LES INSTRUCTIONS RELATIVES A LA SECURITE. Veuillez conserver ce