Votes - 1, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
10.Select and Move Button( / ) Use this button to move to or select an item within a menu. The buttons on the top of the projector are touch buttons. Touch them lightly with your fingers to use them. The label is attached to the bottom of the product. Unpacking Warranty Card/ Registration Card Quick Installation Guide User Manual CD (Not available in all locations) Power Cable Remote Control/ 1 Batteries Cleaning Cloth Sold separately D-Sub Cable LED Indications .:Light is On .:Light is Blinking 0:Light is Off STAND BY LAMP TEMP Information . 0 0 If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. . . 0 The projector is in normal operating condition. . . 0 This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed. 0 . 0 The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off the inside of the projector. (Lasts for about 1 minute and 30 seconds) . 0 . Refer to Action 1 below if the cooling fan inside the projector is not in normal operation condition. 0 . . Refer to Action 2 below if the lamp cover protecting the lamp unit is not closed properly. 0 0 . Power is turned off automatically when temperature inside of the projector goes beyond the control limit. Refer to Action 3. . . . A problem has occurred when operating the DDP IC in the product. Refer to Action 4. . . . A problem has occurred with the operation of the lamp. Refer to Action 5. . . . The lifetime of the lamp has expired. Refer to Action 6. . . 0 The memory in the product is not operating normally. Contact a service center. . . . The power for the product is not operating normally. Contact a service center. . . . A problem has occurred when operating the color wheel in the product. Refer to Action 4. Clearing Indicator Problems Measures If the symptom remains even after disconnecting and then reconnecting the power cord and turning the projector on again, contact your product provider or our service center. Check whether the screws at the bottom side of the projector are fastened correctly. If they are abnormally fastened, contact your product distributor or service center. Adjust the installation state of your projector by referring to the Installation Precautions section listed above. Cool down your projector sufficiently and then operate it again. If the same problem occurs continually, contact your product distributor or service center. Disconnect and reconnect the power cord and start the projector again. If the same symptom still occurs, contact your product distributor or service center. Turn the power off, wait for a sufficient amount of cooling time and then turn the power on to operate. If the same problem occurs continually, contact your product distributor or service center. Check the lamp usage time on the Information Display screen. If you need to replace the lamp, contact your product distributor or service center. Classification Action 1 Action 2 Action 3 Action 4 Action 5 Action 6 State When the cooling fan system is not in normal operating condition. When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. When temperature inside of the projector becomes too high. When the color wheel fails to operate. The lamp malfunctions after power turns off abnormally or after powering on right after turning off the projector. When the screen becomes darker This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan may cause noise, which does not affect the product performance and is part of normal operation. Rear Side 1. RS-232C port (For service input terminals) 6. HDMI/DVI IN Input port 2. SERVICE Input port 3. VIDEO IN Input port 4. S-VIDEO IN Input port 5. Remote Control Signal Receiver 7. MONITOR OUT terminal 8. PC IN Input port 9. COMPONENT IN Input port 10.POWER Input port | Product Features | Product Views | Remote Control | Product Specifications | 1. ON ( ) Button 2. AUTO Button 3. MENU ( ) Button 4. Move (^ Ў . .)/( ) Button 5. V.KEY-STONE(+/-) Button 6. VIDEO Button 7. S-VIDEO Button 8. P.SIZE Button 9. COMP Button 10. OFF ( ) Button 11. RETURN ( ) Button 12. EXIT ( ) Button 13. INFO STILL Button 14. HDMI Button 15. INSTALL Button 16. P.MODE Button 17. PC Button 1. ON ( ) Used to turn on the projector. 2. AUTO Adjusts the Picture automatically. (Available in PC Mode Only) 3.MENU( ) Used to display Menu Screen. 4.Move(^ Ў. .)/( ) Used to move to or select each menu item. 5. V.KEY-STONE (+/-) Use this when video scenes are distorted or tilted. 6. VIDEO Used to switch to VIDEO Mode. 7. S-VIDEO Used to switch to S-VIDEO Mode. 8. P.SIZE Used to adjust the size of picture screen. 9. COMP Used to switch to COMPONENT Mode. 10.OFF ( ) Used to turn off the projector. 11. RETURN ( ) Returns to the previous menu. 12.EXIT ( ) Used to make Men...