Votes - 2, Average rating: 4.5 ( )

Manafacture: Elkay File size: 106.83 kb File name: Language of manual:

Slide the panel down until it engages the mounting plate. Be sure back panel is firmly engaged before releasing it. 3. Remove bottom access panel from fountain basin and save the screws. EDFP217C: Install the fountain to the back panel and wall using (4) 5/16" x 2" long lag bolts and washers (not provided) through holes in back panel. Tighten securely. EDFP217C W/WALL PLATE: Install the fountain to the back panel using (4) 5/16" x 3/4" long screws and washers (provided) through holes in back panel. Tighten securely. 4. Remove elbow from end of p-trap and attach it to drain tube. Reattach elbow to p-trap and cut waste tube to required length using plumbing hardware and trap as a guide. 5. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the strainer. Turn on water supply and check for leaks. Newly installed water supply line should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT. 6. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not covered by warranty. 7. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust the screw on regulator item 10 by using a small screwdriver through the small hole in the push button item 3 (See Fig. 11). Clockwise adjustment will raise stream height and counter-clockwise will lower stream height. For best adjustment stream should hit basin approximately 6-1/2" (165mm) from bubbler. 8. Replace bottom access panel to fountain using the screws provided. Tighten securely. TROUBLE SHOOTING AND MAINTENANCE 1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire. CAUTION: Do not file or cut orifice materials. 2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 7 stated above. 3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it reaches a positive stop, approximately 3/4". 97705C (Rev. J - 8/07) PAGE 6 EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC FIG. 7 FIG. 8 7 8 9 6 21 19 20 NOTE: WHEN INSTALLING REPLACEMENT BUBBLER AND PEDESTAL, TIGHTEN NUT (ITEM 9 OR 20) ONLY TO HOLD PARTS SNUG IN POSITION. DO NOT OVER TIGHTEN. FIG. 923 16 Installing back panel: When installing back panel (item 16) without mounting plate accessory MP20 or MP20RA, attach (4) channel braces (item 23) as shown in FIG. 9. Remove the protective backing from the tape installed on the brace. Line up the corresponding holes in the brace and back panel and press firmly in place. PAGE 7 97705C (Rev. J - 8/07) EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC PARTS LIST DESCRIPTION DRAIN RETAINING NUT PUSH BUTTON PUSH BUTTON SLEEVE REGULATOR HOLDER ORIFICE ASSY HOUSING ASSY PEDESTAL BUBBLER LOCKNUT REGULATOR CAP SCREW SCREW - #10-24 X .50 PHTC STRAINER FOUNTAIN ARM - SHORT FOUNTAIN ARM - LONG FOUNTAIN ARM - LONG (GLASSFILLER) BOTTOM COVER PLATE - SHORT BOTTOM COVER PLATE - LONG BACK PANEL RH ADA BACK PANEL LH ADA HEX NUT REGULATOR MOUNTING BRACKET GASKET - (VR MODEL ONLY) BUBBLER - NIPPLE - (VR MODEL ONLY) BUBBLER - (VR MODEL ONLY) POLY TUBING (CUT TO LENGTH) BRACE-CHANNEL TEE - 1/4 BRACKET - HANGER PANEL FIG. 10 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 NS NS PART NO. LK464 15005C 45662C 45663C 50986C A54874 56011C 55997C 75580C 61313C 75672C 112627543890 55996C 28782C 28783C 27959C 55000661 55000665 28250C 28252C 40045C 27057C 100322740560 15009C 45392C 56092C 28234C 70682C 27090C 14 SEE FIG. 7 OR 8 16 SEE FIG. 11 12, 15 13 22 1 3 4 17 10 18 FIG. 11 2 5 11 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 97705C (Rev. J - 8/07) PAGE 8 ...

Download now

Please, enter two numbers from picture: