Votes - 2, Average rating: 5 ( )

Manafacture: Vita Spa File size: 4.31 mb File name: Language of manual:

NOTE: This setting only alters the temperature for the rest of the day. Go to section “E. HEAT DAYS & TEMPERATURE” on page 8 to make permanent changes. IMPORTANT: When your spa is activated or temperature is adjusted, the spa goes through a 2-. minute calibration cycle. The controller will evaluate the temperatures at the heater and water in the spa and will determine proper operation and heating needs. The calibration process is indicated by the flashing of the heater LED on the L60 Control Center display. xStream Duo Pro Therapy Control Center Operates functions on therapy portion of Duo Pro PAGE 6 THERAPY PROGRAMMING INSTRUCTIONS THERAPY PROGRAMMING INSTRUCTIONS REFER TO PROGRAMMING INSTRUCTIONS ON PAGE 21 FOR QUICK PROGRAMMING STEPS A. PROGRAMMING MENU ..................................................... Note: All programming functions are shown sequentially. To access any specific programming step, you have to enter programming from the beginning, as explained here. Press and hold for three (3) seconds until “dISC” is on the screen to enter the programming menu. To exit programming mode, press , or at any point in the sequence or wait for 10 seconds (without pressing any button). B. SELF - DIAGNOSTIC TOOL ............................................... Note: This feature is operational on all Control Boards Rev J and up. Your spa controller offers the latest state-of-the-art diagnostic tool. To start the test, press while the display is showing "diSC". This test will run the equipment sequentially for two (2) minutes. To cancel the self-test at any time, press . Once the test is completed, the message "good" will be displayed if your spa operates properly. If a problem is found, the malfunction code will be displayed. Please contact your dealer for corrective action. C. HEATING .......................................................................... Your spa is pre-programmed from factory to run on AutoHeat mode every day of the week. That means whenever the temperature of the water falls 1.F (0.5.C) below the set temperature, the ICSTM control will start the heating cycle and run it until the temperature reaches 1.F (0.5.C) above the set temperature. Note: Refer to Section E. HEAT DAYS & TEMPERATURE for how to change this setting. To save even more, you may switch it to ECONOMY mode, where the heating cycle will only come on during programmed filtration hours. (See “Filtration Cycle” below). Note: In ECONOMY mode, if at the end of filtration cycle the water has not reached the set temperature, the heating cycle will stop. This mode is used for energy conservation, the same way you would control your heat or air conditioning in your house. D. FILTRATION CYCLE .......................................................... Your spa is pre-programmed from the factory to run the filtration cycle for two hours in the morning and two hours in the evening. It is recommended that filtration hours be set to the minimum necessary to maintain water quality. Notes: Please review this setting upon installation. Some Control Boards programmed for AH may jump the filtration hours setting. If that happens, change from AH to ECO, program the desired filtration hours and change back to AH. During filtration, the water temperature may rise slightly, therefore to prevent overheating during the warmer months of the year, do not program filtration for more than 6 hours a day (4 hours in very hot climates). Keeping your set temperature a few degrees below your desired temperature will aid in controlling water temperature. 3s TO START SELF TEST TO CANCEL SELF TEST continues on next page Turns filtration On/Off on shown hour. 12: -Off 12: F Filtering Cycles up through filtration hours USE ARROWS TO CHANGE BETWEEN MODES FACTORY DEFAULTS 12: -AM 12: -PM 1: - 1: - 2: - 2: - 3: - 3: - 4: - 4: F 5: - 5: F 6: - 6: - 7: - 7: - 8: F 8: - 9: F 9: - 10: - 10: - 11: - 11: - PAGE7 TO CHANGE TO INDIVIDUAL DAYS OF THE WEEK: 7 – Saturday 6 – Friday 5 – Thursday 4 – Wednesday 3 – Tuesday 2 – Monday 1 – Sunday continues on next page USE ARROWS TO CHANGE TEMPERATURE USE ARROWS TO CHANGE .F to .C 12/24 HOUR MINUTES MONTH DAY YEAR GOES BACK TO THE BEGINNING USE ARROWS TO CHANGE THERAPY PROGRAMMING INSTRUCTIONS E. HEAT DAYS & TEMPERATURE ............................................ Your spa is pre-programmed from factory to heat “All” days, “hd=A”. It has however the ability to be programmed for different temperatures on different days of the week. To do so, follow these steps: Example: Let's assume that you don’t normally use the spa between Mondays and Thursdays and you want to save on your electric bill by reducing the spa’s energy consumption. 1. While the display shows “hd=A” press . The display will show the heat day. Press again until the desired heat day is selected ....................... 2. Press to display temperature for the day selected. Press and hold to lower temperature to, for instance, to 80.F (27.C). Press to increase the tempera...

Download now

Please, enter two numbers from picture: