|
manual abstract
Rotate hinge (A) to position the gasket notch to the inside, then fasten hinge (A) and the bracket to the left side and the top brace to the right side. See Fig. 3. Fig. 1 Hinge (A) Hinge Stop Pin Hinge (B) Screws Fig. 2 Top Panel Fig. 3 Hinge (A) Bracket Screw Top Brace Gasket Notch Screw 14 4) Remove hinge (B) from the right side of the unit and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge (B) to the left side. See Fig. 4. 5) Rotate the top panel 180° from its previous position. This brings the notch that was previously in the right rear to the left front. See Fig. 5. Hook the rear part of the panel on the body, then secure the front with the 2 screws removed in step 2. 6) Remove the 2 screws attaching the door handle and also remove the other 2 screws indicated in the illustration. Use 2 of the screws to attach the handle to the other side of the door and attach the other 2 screws in the remaining 2 holes. See Fig. 6. 7) Attach the door to hinge (A), then continue to maintain a hold on the door. Screw the hinge stop pin into hinge (B) until it is tight. See Fig. 7. Notch Top Panel Hinge Stop Pin Hinge (B) Fig. 4 Fig. 5 Door Handle Screws Fig. 6 Fig. 7 Hinge (B) Filler Screws Screws 2. AM-50BAE-DS, AM-50BAE-ADDS a) Overlay Panel Fabrication and Attachment IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Overlay Panel Parts No. Description Part Number Qty. 1 Threaded Wood Insert 4A4004-01 6 2 T2 Screw 4.8 SS 7P32-0408 3 3 Pan Head Screw M4.25 SS 7C12-0425 4 4 Truss Head Screw M4.8 SS 7C32-0408 2 5 Canoe Clip 4A0629-02 2 6 Sheet Metal Bracket 4A3998-01 1 1 2 3 4 5 6 15 (2) Overlay Panel Specification Use the specification that applies to your icemaker (AM-50BAE-DS or AM-50BAE-ADDS) and the directions that follow to prepare your overlay panel. (a) AM-50BAE-DS ( ) ( ) ( ) ( ) ( ) ( )() () () () AM-50BAE-DS Overlay Panel Specification Overlay Panel Height 29 17/32" (750 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum 16 (b) AM-50BAE-ADDS ( ) ( ) ( ) ( ) ( ) ( )() () () () AM-50BAE-ADDS Overlay Panel Specification Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum 17 18 3) Screw the 6 threaded wood inserts into the 1/4" holes drilled in the previous step. Make sure that the inserts are threaded straight and that the tops of the inserts are flush to the overlay panel surface. Otherwise, the overlay panel cannot be properly fastened to the door. 4) Mount the door handle hardware. Hoshizaki recommends that the door handle hardware be mounted on the edge opposite of the door hinge side (optional hinge reversal is covered in step 6). Countersunk screw heads are required to ensure that the hardware fasteners do not interfere with the overlay panel fitting flush with the door. 5) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out the bottom of the door slightly and gently remove the door from hinge (A). See Fig. 10. If you are leaving the door right-hinged, skip to step 7. If you would like to reverse the door hinges, proceed to step 6. (3) Fabrication of Overlay Panel Fabricate the overlay panel as outlined in the applicable specification on the previous pages and the instructions below. 1) Rout a channel at the bottom of the overlay panel to the proper dimensions. See "(C) Routed Area" in the specification diagram and Fig. 8. 2) Drill six 1/4" diameter (hardwood may require slightly larger diameter) holes 3/8" (10 mm) deep in the locations designated. See "(A) Threaded Inserts" and "(B) Threaded Inserts" in the specification diagram and Fig. 9. CAUTION Use care when drilling holes for mounting hardware. All drilled holes must be straight and drilled to the correct diameter and depth. Routed Channel Holes Holes Fig. 8 Fig. 9 Fig. 10 Hinge Stop Pin Hinge (B) Hinge (A) 19 Screws f) Remove hinge (C1) from the top right part of the door, flip it and reattach to the bottom left. Remove hinge (C2) from the bottom right part of the door, flip it and reattach to the top left. See Fig. 15. Proceed to step 7. d) Remove hinge (B) from the right side of the unit and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge (B) to the left side. See Fig. 13. e) Rotate the top panel 180° from its previous position. This brings the notch that was previously in the right rear to the left front. See Fig. 14. Hook the rear part of the panel on the body, then secure the front with the 2 screws removed in step 6a. 6) If you would like to reverse the door hinges, do the...
Other models in this manual:Other Kitchen Appliances - AM-50BAE-AD (1.57 mb)
Other Kitchen Appliances - AM-50BAE-DS (1.57 mb)