Login: 105856 REV. D INTRODUCTION Your new multimode matrix printer offers bidirectional logic-seeking printing at 400 cps in draft mode, memo quality printing at 180 cps and up to 120 cps in near-letter-quality correspondence mode. Because of its multimode capabilities, this printer is suited for applications where multiple printers would otherwise be required. True lower case descenders and simultaneous underlining are possible. An adjustable printhead gap accommodates forms up to six parts in thic
Therefore, when calculating the value of each column of graphics the value of bit 7 (which is 64) must be added to the value of the print wires. The resulting value for column 1 is then 127 (63 plus the value of bit 7). 4-45 Column 2 contains no dots and therefore column 2 has a value of 64 (0 plus bit 7). This is also true for columns 3,4 and 5. In column 6 all six print wires are fired so column 6 has a value of 127 (63 plus bit 7). Columns 7,8,9,10 and 11 also have a value of 127. In column
NOTE To eject a cut sheet form for any reason, press the Form Feed Key. Figure 3-7: Tear Off Bar Scale 3-10 Forms Handling User’s Guide NOTE If forms length is between 4.5” and 6.0”, verify that the Vertical Gap Position Feature is set to 0.0” (located under M8 Form Thickness in the setup mode). See Section 4.6 for further instructions on how to change this setting. Failure to set Vertical Gap for these forms may cause trailing edge of form to catch under guide during loading. Figure 3-8: Loadin
387002, Rev. E ® ™ AMT ACCEL-6300 P R I N T E R S E R I E S User's Guide Unpacking Set Up Loading Paper Control Panel Cleaning & Maintenance Solving Problems Bottom-Feed Tractors Bar Codes Interfaces Code Sets Specifications Document No. 387002 .. Revision E AMT Datasouth Corp. 4765 Calle Quetzal Camarillo, CA 93012 TEL: (805) 388-5799 FAX: (805) 484-5282 WEB: amtdatasouth.com User's Guideii Preface User's Guide Preface Thank you for selecting an AMT Datasouth® ACCEL™-6300 series printer. Using
................................ ................................ .... 2 Unpackin g ................................ ................................ ................................ ....... 2 Package Contents ................................ ................................ ........................... 3 Placing the Printer ................................ ................................ .......................... 4 Connecting the Powe r Cord ................................ ...................
The value of 4 lines per inch .......... ESC A SI 1B 41 0F 27 б5 15 variable n defines the line spacing distance: 6 lines per inch .......... ESC A LF 1B 41 0A 27 б5 10 8 lines per inch .......... ESC A BS 1B 41 08 27 б5 8 Line spacing = n x 1/72-inch (Epson JX & IBM XL24) 12 lines per inch........ ESC A ENQ 1B 41 05 27 б5 5 Line spacing = n x 1/60-inch (Epson LQ-2550) Note: When the IBM XL24 emulation is active, the Set Vertical Units sequence forces the vertical spacing unit to either 1/7
D Contents... Table of Introduction.............................................................. i 1. Before Using the ATB Printer.........................1-1 1.1 Checking the Package ....................................................... 1-2 1.2 Names and Functions ........................................................ 1-3 2. Operation..........................................................2-1 2.1 Connecting the ATB Printer..............................................2-2 2.2 Turning the
110621 A IMPORTANT SAFETY INSTRUCTIONS AND OTHER NOTICES • This label printer complies with the requirements in Part 15 of FCC rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interface to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference. • Place the printer on a flat, firm and solid surface. • Do not place the printer near a heat source or near water. • Refer to the speci
0.1 0.1 3.9 1.9 0.01 Box would also work. % Box draw % botX(in.) botY(in.) topX(in.) topY(in.) lwidth(in.) Box 0.1 0.1 3.9 1.9 0.01 Box Fastmark 600 Series User's Guide Demo Label showing use of Print Utility Procedures After the file Pal_Procs_and_Formats.txt has been copied to the printer, a number of new procedures are now defined in the printer (until powered off). These procedures have been written specifically to demonstrate how to use the PALTM Print and Program operators to produce print
h width multiplier ‘1’ to ‘9’ and ‘A’ to ’ O’. ‘0’ stands for default. v height multiplier ‘1’ to ‘9’ and ‘A’ to ’ O’, ‘0’ stands for default. eee bar code height This is ignored for box, line and graphics. It represents point size for font ‘9’ and symbol set for Courier font** . yyyy Y coordinate xxxx X coordinate
