Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
It is the best device for an inkjet printer, and it will definitely decrease your printing costs. Before using this system, please read this manual carefully. The pictures in this manual may be different with the real ones. It’s just for your reference. Note: The pictures in this manual may be different with the real ones. Here just for your reference. I. Opening Guide 1. Accessories 1) Continuous ink supply system ……………………………………………1 2) Air Filter ………………………………………………………………….1 3) Sponge …………………………………………………………………….1 4) Injector …………………………………………………………………….1 5) Long needle …………………………………………………………….....1 6) Short needle …………………………………………………………….....1 7) Protection clamp …………………………………………………………..1 8) Installation Manual ………………………………………………………..1 9) Certificate on free installation………………………………………………1 Pic. 1-1 Pic. 1-2 2. Inspection before installation A. Check whether all the accessories are present. B. Check whether the system is retrieved normally or too much air is remained in the connecting tubes (length over 20cm). II. Printer test 1. Check printer status to see whether it is normal or not, and check its mechanics for smooth and any damage. 2 Enter nozzle test option (2-1), print nozzle test sheet to see whether nozzle is normal (2-2, 2-3). Pic. 2-1 Pic. 2-2, 2-3 3. If printer is alright, please print a picture to see the result. Ill. Installation Procedures 1. Remove ink from the air balance tube Place the system on the table, check if there is any ink in each of the air balance tube. If yes, you need to remove the ink in the balance tubes by the following steps: 1) Pull out the sealed plug of the balance tube (3-1-1). 2) Use the injector to draw all ink out. 3) Put the sealed plug back. 4) Put the sealed plug back. 4) Pull refill plug out. 5) Inject ink to the ink tanks according to their color. 6) Put refill plug back. 7) Check all the plugs to make sure they are completely sealed. Pic. 3-1-1 Pic.3-1-2 2. Replace the air balance plugs Put this system on the right side of printer, tidy up ink flow tubes, pull out an air balance plug and replace it with an air filter with the bigger side downwards. 3. Move out cartridge holder Insert screwdriver like, screw screwdriver like until take cartridge cover off. 4. Install the system ink cartridges Take cartridges out. Install CISS cartridges according to printer indication and press cartridge down to the place. 5. Attach tubes Tear sponge seal off. Tidy up ink tube. Stick rack onto the printer cover like. Make sure that tube and rack will not fall off while printing. Do not twist ink tube. 6. Check wire length Move cartridge holder to left side, then to right side, check if the tube is too long or too short. Move cartridge holder to right side, check if ink tube will fall down during movement, if fall down, then the holder will be blocked during printing. Generally, before shipment, we have adjusted the tube to the right size, please double check before printing. 7. Adjust wire length If step 6 is ok, then there is no need to go through this step. If the tube length is too short then lengthen it, if too long then shorten. If the tube falls down, you need adjust the angle of sticker to prevent falling. 8. Take place meter off Tidy up ink tube. Tear seal off, attach fixation like. Press ink tube while closing printer cover to avoid deforming of ink tube. 9. Prepare for printing Plug power wire on (3-9-1), turn printer on. Check whether printer and ink tube can run normally. Close printer cover and check whether it is strange noise while printing. Pic. 3-9-1 10. Check printer nozzle Enter printer nozzle inspection option (3-10-1), print nozzle test sheet. If it is ok (3-10-2)), then can run printer. If line is missing (3-10-3), please clean the nozzle. If just one color is missing (maybe there is air in nozzle). If it is still a little line missing after several times cleaning, please turn printer off and let printer stay turned off for one hour or more. Please contact local distributor if still have problem. Pic.3-10-1 Pic. 3-10-2, 3-10-3 IV. Notice It requires to change cartridges while printing (4-1-1) and ink light flash (4-1-2). Press ink button to move out cartridge holder. Press chip reset button for 3 seconds (4- 1-3), repress ink button to move back cartridge holder, then ink amount shows 99% again. Redo nozzle inspection and printer can run normally if it ...
Other models in this manual:Printers - C82 (314.82 kb)