Votes - 2, Average rating: 5
(
)
)
|
Other manuals for this model:
manual abstract
4 Press the Cancel button to start feeding. Note: Please be careful when you open the rear cover. The inside of the printer maybe hot. 5 Printing is started. Close the rear output tray after the printing is completed. 3 USING PRINT MATERIALS 3.11 Printing on Labels Guidelines • Only use labels recommended for laser printers. • Verify that the labels’ adhesive material can tolerate fusing temperature of 200°C (392°F) for 0.1 second. • Make sure that there is no exposed adhesive material between the labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to printer components. • Do not feed a sheet of label through the printer more than once. The adhesive backing is designed for one pass through the printer. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. 1 Open the rear output tray. Load labels in the manual feeder with print side up. 2 Adjust the guide to fit the width of the labels. 3.12 USING PRINT MATERIALS 3 When you print on labels, you must select Manual Feed for Source from the software application, and then select the correct paper size and type. For details, see page 4.6. Note: Please be careful when you open the rear cover. The inside of the printer maybe hot. 4 Press the Cancel button to start feeding. Printing is started. 3 Close the rear output tray after the printing is completed. Note: To prevent labels from sticking to each other, do not let the printed label sheets stack up as they are printed out. Printing on Transparencies Guidelines • Only use transparencies recommended for use in laser printers. • Ensure that transparencies are not wrinkled, curled, or have any torn edges. • Hold the transparencies by the edges and avoid touching the print side. Oils deposited on the transparency can cause print quality problems. • Be careful not to scratch or leave fingerprints on the print side. 1 Open the rear output tray. Load transparencies in the manual feeder with print side up, and the top with the adhesive strip going first. USING PRINT MATERIALS 3.13 2 Adjust the guide to fit the width of the transparencies. 3 When you print on transparencies, you must select Manual Feed for Source from the software application, and then select the correct paper size and type. For details, see page 4.6. Note: Please be careful when you open the rear cover. The inside of the printer maybe hot. 4 Press the Cancel button to start feeding. Printing is started. Close the rear output tray after the printing is complete. Notes: • To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are printed out. • Place transparencies on a flat surface after removing them from the printer. 3.14 USING PRINT MATERIALS Printing on Card Stock or Printing on Card Stock or Custom-sized Materials Postcards, 3.5 by 5.83 in.(index) cards and other custom-sized materials can be printed with this printer. The minimum size is 76 by 127mm(3.0 by 5.0 in.) and the maximum size is 216 by 356mm(8.5 by 14 in.). 3 1 Open the rear output tray. Load print material with print side up, short edge first and against the left edge of the feeder. Guidelines • Always insert the short-edge into the Manual Feeder first. If you want to print in landscape mode, make this selection through your software. Inserting paper long-edge first may cause a paper jam. • Do not print on media smaller than 76mm (3.0 in.) wide or 127mm(5.0 in.) long. • When you print on 76mm x 127mm sized media with loading into the tray, open the rear output tray. 2 Adjust the guide to fit the width of the material. USING PRINT MATERIALS 3.15 3 When you print on card stocks or the custom-sized paper, you must select Manual Feed for Source from the software application, and then select the correct paper size and type. For details, see page 4.6. Note: If the size of your print material is not listed in the Size box in the Paper tab of the printer driver properties, click Add Custom button and set the size manually. See page 4.6. 4 Press the Cancel button to start feeding. Printing is started. Close the rear output tray after the printing is completed. Printing on Preprinted Paper Preprinted paper is paper that has some type of printing placed on it before it is sent through the printer (paper that has a preprinted logo at the top of the page, for example). Note: Please avoice using carbon paper because it may cause the printer a mechanical trouble. Guidelines • Letterheads must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the printer’s fusing temperature of 400 °F (205 °C) for 0.1 second. • Ink on letterheads must be non-flammable and should not adversely affect any printer rollers. • Forms and letterheads should be sealed in a moisture-proof wrapping to prevent changes during storage. • Before you load preprinted paper as forms and lette...
Other models in this manual:Printers - ML-1750 (3.73 mb)
Printers - ML-1750G (3.73 mb)
Printers - ML-1755 (3.73 mb)
Printers - ML-1757 (3.73 mb)