Votes - 2, Average rating: 5
(
)
)
|
Photos and specs Sony DPP-FP67 |
Other manuals for this model:
manual abstract
Fingerprints or dust on the ink ribbon may result in imperfect printing. • Do not rewind the ink ribbon and use the rewound ink ribbon for printing. Otherwise, proper printing results will not be obtained, or a malfunction may occur. If the ink ribbon does not click into place, remove it and then re-insert it. Only when the ink ribbon is too slack to be loaded, keep pressing the core of the ribbon and wind the ink ribbon in the direction of the arrow to remove the slack. Do not wind the ribbon in the directions shown here • Do not disassemble the ink ribbon. • Do not pull out the ribbon from the ink ribbon. • Do not remove the ink ribbon while printing. • Avoid placing the ink ribbon in a location subject to high temperatures, high humidity, excessive dust or direct sunlight. Please store it in a cool and dark place and use it within a short period from the date of production. Depending on the storage conditions, the ink ribbon may deteriorate. Use of such an ink ribbon may affect the printed results, for which we cannot guarantee or compensate. Inserting the print paper 1 Open the paper tray cover. Hold the parts on both sides of the paper tray cover (shown with arrows) and open the paper tray cover. 2 Set the print paper into the paper tray. 10 GB 3 Close the paper tray cover. • To avoid paper jam or malfunctions of the printer, 4 Open the slide cover. 5 Insert the paper tray into the printer. Notes • You can set up to 20 sheets of print paper. Riffle the print paper thoroughly. Insert the print paper with the protective sheet facing up. Remove the protective sheet from the tray. • If there is no protective sheet, insert the print paper into the paper tray with its printing surface (the side with no imprint) facing up. • Do not touch the printing surface. Fingerprints or contamination on the printing surface may result in imperfect printing. • Do not bend the print paper, or cut the print paper from the perforations before printing. make sure of the following before printing: – Do not write or type on the print paper. – Do not attach a sticker or stamps on the print paper. – When adding print paper to the paper tray, be sure that the total number of print paper sheets does not exceed 20 sheets. – Do not insert different types of print paper together into the paper tray. – Do not print on used print paper. Printing an image twice on the same paper will not make the printed image thicker. – Use the print paper for this printer only. – Do not use print paper ejected without printing. Notes on storing the print paper • To store print paper in the tray, remove the paper tray from the printer and close the slide door of the paper tray. • Avoid storing the paper with the printed faces touching each other or in contact with rubber or plastic products, including vinyl chloride or plasticizer for an extended period of time; color changes or deterioration of the printed image may occur. • Avoid placing the print paper in a location subject to high temperatures, high humidity, excessive dust or direct sunlight. • When you are going to store partially-used print paper, store it in its original bag or a similar container. Preparations 11 GB Connecting to the AC power source 1 Insert the plug of the AC adaptor into the DC IN 24 V jack on the back of the printer. 2 Connect one plug of the AC power cord to the connector of the AC adaptor and the other plug to the wall outlet. Notes • Do not place the printer in an unstable location such as on a wobbly table. • Leave enough room around the printer. The print paper emerges from the back a few times during printing. Keep 10 cm (13/32 inch) or more space at the rear of the printer. • Connect the AC adaptor to an easily accessible wall outlet close by. If trouble occurs while using the adaptor, immediately shut off the power by disconnecting the plug from the wall outlet. • Do not short the plug of the AC adaptor with a metallic object, as this may cause a malfunction. • Do not use the AC Adaptor placed in a narrow space, such as between a wall and furniture. • When you have finished using the AC adaptor, disconnect the AC power cord from the DC IN 24 V jack of the printer and from the AC power sources. • The printer is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the printer itself has been turned off. • A socket outlet should be as close as possible to the unit and easily accessible. AC adaptor AC power cord To the wall outlet 10 cm (13/32 inches) To use your Printer abroad - Power sources You can use your Printer and the AC Adaptor (supplied) in any country or region where the power supply is within 100 V to 240 V AC, 50/60 Hz. Do not use an electronics transformer (travel converter), as this may cause a malfunction. 12 GB Operations in an initial state When the photo printer is turned on without a memory card inserted or a PC connected, the initial display below appears on the screen. When the printer is not opera...
Other models in this manual:Printers - DPP-FP77 (2.69 mb)