Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
120/60/1 (SR24C model only) . 120/208(3W)/60/1 (SR24H model only) . 120/240(3W)/60/1 (SR24H model only) OPTIONS . Detergent pump - factory installed (chemical sensing module included) MODELS . SR24H – High Temperature Sanitizing . SR24C – Chemical Sanitizing ACCESSORIES - field installed . Detergent and/or rinse agent pump (chemical sensing device suggested) . Chemical sensing device (SR24H only) . Stainless steel top and side panels . Stainless steel base with 6" legs . 17" stainless steel stand . Pressure regulator valve Specifications, Details and Dimensions on Inside and Back. SR24 Model SR24H Built in Booster 180°F Rinse (Shown with optional side and top panels) SR24 DISHMACHINE 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • Page 2 of 4 F-40028 – SR24 Dishmachine DETAILS AND DIMENSIONS SR24 DISHMACHINE 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • F-40028 – SR24 Dishmachine Page 3 of 4 INSTALLATION REQUIREMENTS AND INSTRUCTIONS 1. A single fill and rinse pipe connection is required. 6' flex hose supplied. 2. The electrical connection location for a 3.4" electrical connector (11.8" diameter hole) is provided for the SR24H model only. 3. The required electrical cord and plug are supplied on the SR24C model only. 4. Important: The sodium hypochlorite container should be placed on the floor (SR24C model only). 5. If the sodium hypochlorite container is to be placed in a cabinet adjacent to the machine, a 1.2" diameter hole is required in the cabinet to run the bleach supply line through. 6. Pumped drain 3.4" MPT fitting 10' hose supplied. 7. A supply line strainer is required. (By others) 8. If water flowing pressure is over 28 psi, install a PRV (not supplied). If water flowing pressure is under 22 psi, the supply line pressure must be increased. SR24 DISHMACHINE 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • As continued product improvement is a policy of Hobart, specifications are subject to change without notice. Page 4 of 4 F-40028 – SR24 Dishmachine SPECIFICATIONS DESIGN: Front opening, equipped with stainless steel front. Freestanding Models – Top and side panels are optional. Undercounter Models – Not equipped with side or top panels. Adjustable feet lower overall height to 345.8" minimum and raise it to 355.8" maximum. CONSTRUCTION: 16 gauge stainless steel tank bottom with 18 gauge stainless steel base, chamber and door. PUMP: Centrifugal-type, integral with motor, vertically mounted. Pump capacity is 45 U.S. gallons per minute. MOTOR: Built to Hobart specifications, 1.2 H.P., single phase, furnished for 120/60/1, 120/208(3W)/60/1 or 120/240(3W)/60/1 electrical specification. Factory sealed lubrication. RACKING: Will accommodate most racks from 10" x 20" (half racks) to 20" x 20". Will also accept 16" x 18" cafeteria trays. WASH AND RINSE CYCLE: Completely automatic, controlled by an electrically energized synchronous timer. Closing the door actuates the operating cycle. When the amber cycle light goes out, the operating cycle is complete (185 seconds for the SR24H models and 215 seconds for the SR24C model). The cycle may be interrupted at any time by opening the door. Cycle continues when the door is closed. WASH: Revolving upper and lower hydrosweep wash arms with unrestricte...
Other models in this manual:Dishwashers - DISHMACHINE SR24H (333.39 kb)