Votes - 1, Average rating: 5 ( )

Manafacture: Fisher & Paykel File size: 820.63 kb File name: f6717b1f-3303-4dab-bb55-458af156bde9.pdf Language of manual:

If spotting and poor drying are problems, increase the amount of rinse aid dispensed by rotating the dial to a higher number. The dial is located under the dispenser cap. The indicator will be dark when full and will show clear when it is time to refill. To add liquid rinse aid, turn dispenser cap 1/4 turn counterclockwise and lift out. Pour in rinse aid until liquid touches the indicated fill level. Replace cap. Do not overfill since this can cause oversudsing. Wipe up any spills with a damp cloth. The dispenser holds enough for 35 to 140 washes, depending on setting. Factors Affecting Performance Water Pressure The hot water line to dishwasher must provide water pressure between 20 and 120 psi. Low water pressure may occur when laundry or showers are in operation. Wait until water use is reduced before starting dishwasher. Water Temperature Hot water is needed for best dishwashing and drying results. Water entering dishwasher should be at least 120°F (49°C) to give satisfactory results. To check water temperature entering dishwasher: • Turn on hot water faucet nearest dishwasher for several minutes to clear cool water from pipes. • Hold a candy or meat thermometer in stream of water to check the temperature. • If temperature is below 120°F (49°C), have a qualified person raise the hot water heater thermostat setting. Important: Before starting a cycle, run hot water to clear cool water from pipe. Adjustable setting Dispenser Opening Indicator Dispenser Cap 9 Care and Cleaning Burn Hazard Allow heating element to cool before cleaning the interior. Failure to do so can result in burns. Outside—Occasionally wipe with a mild nonabrasive detergent and water. Rinse and dry. Inside—The inside of the dishwasher is self- cleaning with normal use. If needed, clean around the tub gasket area with a damp cloth. The filter is self-cleaning. A glass trap located in the center of the filter is designed to collect pieces of broken glass, straws, bones and pits. To remove items in glass trap, grasp handle, lift out, empty and replace. Note: Hard water may cause lime deposit buildup on the interior of the dishwasher. For cleaning instructions see “Removing Spots and Film” section. Care of Drain Air Gap If a drain air gap was installed for your built-in dishwasher, check to make sure it is clean so the dishwasher will drain properly. A drain air gap is usually mounted on countertop and can be inspected by removing the cover. This is not part of your dishwasher and is not covered by warranty. Property Damage Hazard Freezing temperatures may cause water lines to rupture. Be sure all supply lines to and circulating lines within dishwasher are protected. Failure to do so could result in property damage. Winterizing A dishwasher left in an unheated place should be protected from freezing. Have a qualified person do the following: To Disconnect Service: 1. Turn off electrical power to the dishwasher at the supply source by removing fuses or tripping circuit breaker. 2. Shut off water supply. 3. Place a pan under the inlet valve. Disconnect water line from inlet valve and drain into pan. 4. Disconnect drain line from pump and drain water into pan. Overfill Protector—keeps dishwasher from overfilling and is located in the left front corner of the tub. • Clean occasionally with household cleaner containing vinegar or bleach to dissolve any buildup. • Overfill Protector should move up and down freely about one inch. If it does not move, lift and clean underneath. Note: See Installation Instructions for more details. To Restore Service: 1. Reconnect the water, drain, and electrical power supply. 2. Turn on water and electrical power supply. 3. Fill both detergent cups and run dishwasher through a NORMAL cycle. 4. Check connections to make sure they do not leak. Note: See Installation Instructions for more details. 10 Connecting and Disconnecting the Portable/ Convertible Dishwasher The portable/convertible dishwasher must be connected to a faucet and electrical outlet each time it is used. Follow directions on this page to properly connect dishwasher. Faucet Adapter Assembly For Outside Threaded Faucet Use Thin Washer Only Adapter (Dual Thread) Connecting the Portable Faucet Adapter Assembly Collar Coupler For Inside Threaded Faucet Use Thick and Thin Washers Two Brass Screens should be below the rubber washers IMPORTANT: Make sure door is latched before moving dishwasher. The power cord, faucet coupler and hoses are located in a compartment in back of dishwasher. A special adapter must be installed on faucet before you can connect dishwasher. 1. Remove faucet adapter assembly from literature package. 2. Unscrew existing sink faucet aerator. 3. Check faucet spout to see if threads are inside or outside. • If threads are on inside of faucet spout, use both thick and thin rubber washers. • If threads are on outside of faucet spout, use thin rubber washer only. • If faucet has no threads, an adapter kit with instructions for attachment t...

Download now

Please, enter two numbers from picture: