Votes - 0, Average rating: 0
(
)
)
|
manual abstract
This appliance is identified . according to the European guideline 2002/96/EC on waste electrical and electronic equipment – WEEE. The guideline specifies the framework for an EU-wide valid return and re-use of old appliances. Getting to know your appliance en * Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel ( ON/OFF switch 0 Programme buttons ** 8 Display “Check water supply” @ Salt refill indicator H Rinse aid refill indicator P Door opener X Timer programming * ` Additional options ** h START button )" Programme sequence indicator )* Digital display * depending on model ** Number depending on model Appliance interior 1" Interior light * 1* Top basket 12 Knife shelf * 1: Tablet collecting tray 1B Top spray arm 1J Bottom spray arm 1R Dispenser for special salt 1Z Filters 1b Cutlery basket 1j Bottom basket 9" Dispenser for rinse aid 9* Detergent dispenser 92 Lock for detergent dispenser 9: Rating plate * depending on model Overview of menu The settings can be found in the individual chapters. • Water Hardness •:‹‹ -•:‹. s Intensive drying s:‹‹ -s:‹‚ § Rinse aid §:‹‹ -§:‹‡ ‘ Hot water ‘:‹‹ -‘:‹‚ . Automatic disconnection .:‹‹ -.:‹. en Water softening system/Special salt + Water softening system/Special salt To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 1.2 mmol/l must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Setting The amount of salt dispensed can be set from •:‹‹ to •:‹.. Salt is not required at the set value •:‹‹. 1. Find out about the hardness value of your tap water. Your water utility company will help you with this. 2. Set value can be found in the water hardness table. 3. Close the door. 4. Switch on ON/OFF switch (. 5. Hold down programme button # and press START button h until •:‹.... is indicated on the digital display. 6. Release both buttons. The LED for button # flashes and the digital display )* displays the factory setting •:‹…. To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of •:‹. has been reached, the display jumps back to •:‹‹ (off). 2. Press START button h. The chosen setting has now been stored. Water hardness table . % . . # . . &. . . $ . . !!!"!!!!!!!!!!"!! Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. 1. Open the screw-type cap of the compartment 1R. 2. Fill the tank with water (only required when switching on the appliance for the first time). 3. Then add dishwasher salt (not table salt or tablets). The water is displaced and runs out. As soon as the salt refill indicator @ on the fascia is lit, top up the salt. * depending on model Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/ l). If the water hardness is over 21° dH, special salt must be used. Rinse aid en Switching off salt refill indicator/water softening system If the salt refill indicator @ is impaired (e.g. when using combined detergents containing salt component), it can be switched off. . Proceed as described under “Adjusting the water softening system” and set the value to •:‹‹. The water softening system and salt refill indicator are now switched off. a Caution Never fill the salt dispenser with detergent. You will destroy the water softening system. , Rinse aid As soon as the rinse-aid refill indicator H is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. en Rinse aid 1. Open the dispenser 9" by pressing and lifting the plate on the cover. 2. Carefully pour rinse aid up to the max. mark in the filler opening. 3. Close cover until it clicks shut. 4. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The amount of rinse aid can be set from §:‹‹ to §:‹‡. Please set rinse aid on §:‹† to obtain very good drying results (§:‹† is already set in factory). Change this sett...
Other models in this manual:Dishwashers - S41M65N4EU/25 (1.92 mb)
Dishwashers - S41M65N4EU/28 (1.92 mb)
Dishwashers - S41M65N4EU/32 (1.92 mb)
Dishwashers - S41M65N4EU/43 (1.92 mb)