Votes - 3, Average rating: 4.3 ( )

Manafacture: Amana File size: 1.01 mb File name: 47b44b1a-01ee-402b-9690-5f5ed5dec7f4.pdf Language of manual:

Reconnect the water, drain, and electrical power supply. 2. Turn on water and electrical power supply. 3. Fill both detergent cups and run dishwasher through a NORMAL cycle. 4. Check connections to make sure they do not leak. Note: See Installation Instructions for more details. 11 Connecting and Disconnecting the Portable/ Convertible Dishwasher The portable/convertible dishwasher must be connected to a faucet and electrical outlet each time it is used. Follow directions on this page to properly connect dishwasher. Faucet Adapter Assembly Connecting the Portable Faucet Adapter Assembly Collar Coupler Avoid fire hazard or electrical shock. Do not use an adapter plug, extension cord or remove grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fire or death. Power supply cord with 3-prong grounding plug IMPORTANT: Make sure door is latched before moving dishwasher. The power cord, faucet coupler and hoses are located in a compartment in back of dishwasher. A special adapter must be installed on faucet before you can connect dishwasher. 1. Remove faucet adapter assembly from literature package. 2. Unscrew existing sink faucet aerator. 3. Check faucet spout to see if threads are inside or outside. • If threads are on insideof faucet spout, use both thick and thin rubber washers. • If threads are on outsideof faucet spout, use thin rubber washer only. • If faucet has no threads, an adapter kit with instructions for attachment to a non-threaded spout is available at most hardware stores. 4. Assemble faucet spout as shown. Make sure the two brass screens are located below the rubber washers. Connecting the Portable/Convertible Dishwasher 1. Run water at faucet until it is hot. Turn off faucet. 2. Pull hoses out of compartment. 3. Push collar down and slip faucet connector onto faucet adapter. 4. When connector snaps into place, release collar. 5. Slowly turn on hot water all the way. 6. Plug power cord into grounded outlet. Getting Water While Dishwasher is Running You can get water from the faucet while the dishwasher is connected. However, avoid getting water when the dishwasher is filling or draining. 1. Press red button on coupler to get the water you want. The faucet is set on hot, adjust faucet if you want cold. 2. Be sure hot water is turned back on all the way to complete cycle. Disconnecting the Portable/Convertible Dishwasher 1. When cycle has finished, turn off hot water. 2. Press red button on coupler to release water pressure being careful not to release coupler. 3. Press down on collar to release coupler. 4. Empty remaining water from coupler and return it to compartment. 5. Unplug power cord and return it to compartment. IMPORTANT: A sink spray attachment hose can burst due to constant water pressure while in use. If your spray hose is installed on same water line as the dishwasher, we suggest you disconnect the sink spray attachment and plug the hole. Electrical Connection for a Portable/Convertible Dishwasher An electrical supply of 120 volts, 60 Hz, AC only, 15 amps is required. For your safety, the dishwasher must be grounded. If there is a malfunction or breakdown, grounding will reduce risk of electrical shock. This dishwasher has a power cord with a 3-prong grounding plug. It must be plugged into a mating 3-prong grounding type receptacle, installed and grounded in accordance with the National Electrical Code and any local codes and ordinances. Grounding type wall receptacle Do not under any circumstances cut, remove or bypass the grounding prong from this plug. Converting to Built-In Your portable dishwasher can be converted to a built-in (undercounter) model. A conversion kit No. 154241302 is required and is available from your local dealer or distributor. Instructions are included with the kit. For Outside Threaded Faucet Use Thin Washer Only Adapter (Dual Thread) For Inside Threaded Faucet Use Thick and Thin Washers Two Brass Screens should be below the rubber washers 12 Solutions to Common Dishwashing Problems Before calling for service, review this list. It may save you both time and expense. This list includes common experiences that are not the result of defective workmanship or material in your dishwasher. Food Soils Left on Dishes • Choose another cycle for longer washing time. • Check rack loading section for proper loading—avoid nesting items. • Home water pressure may be too low— should be 20 to 120 pounds per square inch (psi). • Check incoming water temperature. It should be at least 120°F (49°C). (See Factors Affecting Performance.) • Select HI-TEMP WASH option. • Check water hardness. For extremely hard water, it may be necessary to install a water softener. (See Detergent Chart.) • Use fresh detergent. • Check to make sure funnel in top rack is not blocked. • Make sure items are not blocking the spray arms, preventing them from rotating. Dishes not Dry • Select heat dry option. • Make sure the rinse aid dispenser is filled. •...

Download now

Please, enter two numbers from picture: